Lithium carbonate is an important chemical raw material that is widely used in many contexts. The preparation of lithium carbonate by acid roasting is limited due to the large amounts of low-value sodium sulfate waste salts that result. In this research, bipolar membrane electrodialysis (BMED) technology was developed to treat waste sodium sulfate containing lithium carbonate for conversion of low-value sodium sulfate into high-value sulfuric acid and sodium hydroxide. Both can be used as raw materials in upstream processes. In order to verify the feasibility of the method, the effects of the feed salt concentration, current density, flow rate, and volume ratio on the desalination performance were determined. The conversion rate of sodium sulfate was close to 100%. The energy consumption obtained under the best experimental conditions was 1.4 kWh·kg−1. The purity of the obtained sulfuric acid and sodium hydroxide products reached 98.32% and 98.23%, respectively. Calculated under the best process conditions, the total process cost of BMED was estimated to be USD 0.705 kg−1 Na2SO4, which is considered low and provides an indication of the potential economic and environmental benefits of using applying this technology.
In the papermaking industry (reconstituted tobacco), a large number of tobacco stems, dust, and fines are discharged in the wastewater. This high salinity wastewater rich in ionic constituents and nicotine is difficult to be degraded by conventional biological treatment and is a serious threat that needs to be overcome. Electrodialysis (ED) has proved a feasible technique to remove the inorganic components in the papermaking wastewater. However, the fouling in ion exchange membranes causes deterioration of membranes, which causes a decrease in the flux and an increase in the electrical resistance of the membranes. In this study, the fouling potential of the membranes was analyzed by comparing the properties of the pristine and fouled ion exchange membranes. The physical and chemical properties of the ion exchange membranes were investigated in terms of electrical resistance, water content, and ion exchange capacity, as well as studied by infrared spectroscopy (IR) spectra, scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) analyses. The results indicated that the membrane fouling is caused by two different mechanisms. For the anion exchange membranes, the fouling is mainly caused by the charged organic anions. For the cation exchange membrane, the fouling is caused by minerals such as Ca2+ and Mg2+. These metal ions reacted with OH− ions generated by water dissociation and precipitated on the membrane surface. The chemical cleaning with alkaline and acid could mitigate the fouling potential of the ion exchange membranes.
The crystalized mixed salts from the zero liquid discharge process are a hazardous threat to the environment. In this study, we developed a novel electrodialysis (SBMED) method by assembling the monovalent selective anion-exchange membrane (MSAEM) into the bipolar membrane electrodialysis (BMED) stack. By taking the advantages of water splitting in the bipolar membrane and high perm-selectivity of MSAEM for the Cl− ions against the SO42− ions, this combination allows the concurrent separation of Cl−/SO42− and conversion of mixed salts into relatively high-purity monoprotic and diprotic acids. The current density has a significant impact on the acid purity. Both the monoprotic and diprotic acid purities were higher than 80% at a low current density of 10 mA/cm2. The purities of the monoprotic acids decreased with an increase in the current density, indicating that the perm-selectivity of MSAEM decreases with increasing current density. An increase in the ratio of monovalent to divalent anions in the feed was beneficial to increase the purity of monoprotic acids. High-purity monoprotic acids in the range of 93.9–96.1% were obtained using this novel SBMED stack for treating simulated seawater. Therefore, it is feasible for SBMED to valorize the mixed salts into relatively high-purity monoprotic and diprotic acids in one step.
Bipolar membrane electrodialysis (BMED) is a promising process for the cleaner production of organic acid. In this study, the separation mechanism of BMED with different cell configurations, i.e., BP-A, BP-A-C, and BP-C (BP, bipolar membrane; A, anion exchange membrane; C, cation exchange membrane), to produce diprotic malic acid from sodium malate was compared in consideration of the conversion ratio, current efficiency and energy consumption. Additionally, the current density and feed concentration were investigated to optimize the BMED performance. Results indicate that the conversion ratio follows BP-C > BP-A-C > BP-A, the current efficiency follows BP-A-C > BP-C > BP-A, and the energy consumption follows BP-C < BP-A-C < BP-A. For the optimized BP-C configuration, the current density was optimized as 40 mA/cm2 in consideration of low total process cost; high feed concentration (0.5–1.0 mol/L) is more feasible to produce diprotic malic acid due to the high conversion ratio (73.4–76.2%), high current efficiency (88.6–90.7%), low energy consumption (0.66–0.71 kWh/kg) and low process cost (0.58–0.59 USD/kg). Moreover, a high concentration of by-product NaOH (1.3497 mol/L) can be directly recycled to the upstream process. Therefore, BMED is a cleaner, high-efficient, low energy consumption and environmentally friendly process to produce diprotic malic acid.