This article describes the synthesis of titania-silica composites by a sol-gel method using a mixture of silica of rice husk and titanium butoxide sols. Microstructures were examined at calcination temperature in the range of 500 to 700 °C, with temperatures interval of 50 °C. The sintered catalysts were subsequently tested for photodegradation of methylene blue (MB) under ultraviolet and sunlight rays. Physical characteristics were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM)/energy dispersive X-ray spectroscopy (EDS), and Brunauer-Emmett-Teller (BET). The XRD results did not show the presence of silica crystal phase in each sample. The results showed that the highest BET surface area of samples was obtained at the temperature of 650 °C. In sample calcined 500 °C, the activity of the catalyst on MB was relatively similar in both sunlight and ultraviolet rays.
1 April 2020 in Journal of Magnetism and Magnetic Materials
We have been demonstrated the detection of Fe 3 O 4 nanoparticles by using giant magnetoresistance (GMR) sensor based on multilayer and spin valve thin films by using in Wheatstone bridge. The thin films were fabricated by DC magnetron sputtering method. The structure of multilayer thin film is [Co (1,5 nm)/ Cu (1,0 nm)]20 and spin valve thin film is IrMn (10 nm) / CoFe (3 nm) / Cu (2.2 nm) / CoFeB (10 nm). The Fe 3 O 4 nanoparticles were synthesized by chemical coprecipitation method. The nanoparticles show superparamagnetic properties which saturation magnetization of 77 emu/gram and average particle size of 10 nm. The crystal structure of Fe 3 O 4 magnetic nanoparticles was inverse spinel. The output voltage of Wheatstone bridge is linear to the Fe 3 O 4 concentrations (0.1 mg/ml; 1 mg/ml; 10 mg/ml; 100 mg/ml). That gradient was 0.20 for spin valve thin film and 0.07 for multilayer thin film. The gradient shows that spin valve thin film more sensitive than multilayer. The magnetic moment of spin valve thin film was saturated easier than multilayer thin film. The magnetization of spin valve thin film could be saturated by external field of 20 Oe, while multilayer was 5000 Oe. Magnetoresistance of spin valve was 6%, and magnetoresistance of multilayer was 4%.
Voltage control of magnetic anisotropy (VCMA) is one of the promising approaches for magnetoelectric control of magnetic tunnel junction (MTJ). Here, we systematically calculated the magnetic anisotropy (MA) and the VCMA energies in the well-known MTJ structure consisting of Fe/MgO interface with Cr buffer layer. In this calculation, we investigated an alloying between Fe and Cr and a strain effect. We used a spin density functional approach which includes both contributions from magnetocrystalline anisotropy energy (MCAE) originating from spin–orbit coupling and shape magnetic anisotropy energy from spin dipole–dipole interaction. In the present approach, the MCAE part, in addition to a common scheme of total energy, was evaluated using a grand canonical force theorem scheme. In the latter scheme, atom-resolved and -resolved analyses for MA and VCMA can be performed. At first, we found that, as the alloying is introduced, the perpendicular MCAE increases by a factor of two. Next, as the strain is introduced, we found that the MCAE increases with increasing compressive strain with the maximum value of 2.2 mJ/m. For the VCMA coefficient, as the compressive strain increases, the sign becomes negative and the absolute value becomes enhanced to the number of 170 fJ/Vm. By using the atom-resolved and -resolved analyses, we clarified that these enhancements of MCAE and VCMA mainly originates from the Fe interface with MgO (Fe) and are located at certain lines in the two dimensional Brillouin zone. The findings on MCAE and VCMA are fully explained by the spin-orbit couplings between the certain d-orbital states in the second-order perturbation theory.
Electric field (EF) control on magnetic anisotropy energy (MAE) in the system which contains Fe/MgO interface with Cr underlayer was performed by means of first-principles electronic structure calculations. An opposite sign in EF coefficient (y) was observed by introducing Fe/Cr intermixing. This intermixing leads to a substantial rearrangement in the electronic structure due to proximity effects of Fe and Cr. The origin of such an opposite sign in y was discussed along with the modulation of occupied and unoccupied d-band near the Fermi level. By introducing a strain effect, the enhancements of MAE and y were achieved with the maximum absolute values, 2.43 mJ/m 2 and 170 fJ/Vm, respectively. The present result provides a new possible degree of freedom for the EF control in MAE as the underlayer configuration.
In this study, a potential biomaterial detection technology was successfully developed based on giant magnetoresistance (GMR) sensors. The GMR sensors were performed using [Co(1.5 nm)/Cu(x)]20 multilayer structures (x = 0.8, 0.9 and 1.0 nm) fabricated by DC magnetron sputtering. The X-ray diffraction (XRD) patterns showed that Co/Cu film multilayer has a high degree of crystallinity with a single peak correspond to face-centered cubic (111) structure at 2θ = 44.1°. Co/Cu multilayers exhibit soft magnetic behavior with the saturation magnetization (Ms) of 1416, 1463 and 1489 emu/cc and the coercivity (Hc) of 1.5, 1.6, and 112 Oe for x = 0.8, 0.9 and 1.0 nm, respectively. The magnetoresistance (MR) of Co/Cu was about 4.3%, 6.9% and 14.8% for x = 0.8, 0.9 and 1.0 nm, respectively. Furthermore, we used magnetite (Fe3O4) nanoparticles as a biomolecular label (nanotag) synthesized by coprecipitation method. XRD patterns and transmission electron microscopy (TEM) images showed that Fe3O4 had well crystallized and grow in their inverse spinel structure, highly uniform morphology with grain size of about 12 nm. The M-H loop of Fe3O4 exhibit soft magnetic behavior with Ms of 77 emu/gram and Hc of 47 Oe. The GMR sensor design was used to detect a biomolecule such as formaldehyda and α-amylase enzyme with concentration 20 ppm captured using nanoparticles magnetite coated with polyethylene glycol (PEG) polymer for surface functionalization. Various applied magnetic field of 0–600 Gauss has been performed using electromagnetic with the various current of 0–4.5 A. Induction which cause a shift in MR ratio shown the best response with tCu = 0.9nm was about 18.3% and tCu = 1.0nm was about 4.7% for detection formaldehyda and α-amylase enzyme respectively. Furthermore, we present the linearly output signal and saturation signals in real time measurement from sensors. Based on this result, we can conclude that the combination of Co/Cu film multilayer, magnetite, and PEG polymer are potential in biodetection technology.