Kenichi Murakami

Mr. Kenichi Murakami

Data Science Research Division, Information Technology Center, The University of Tokyo
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 January 2019 in IEEE Robotics and Automation Letters
Verified
Journal Article
Open access
KKKeisuke Koyama
Keisuke Koyama
KMKenichi Murakami
Kenichi Murakami
TSTaku Senoo
Taku Senoo
MSMakoto Shimojo
Makoto Shimojo
MIMasatoshi Ishikawa
Masatoshi Ishikawa
In this paper, we propose a combination of sensing and control modules for catching soft objects (i.e., a marshmallow and paper balloon) at a high speed with small deformation. A paper balloon and marshmallow are deformed by a small force and they have individual differences in terms of softness. Therefore, model-based, small-deformation catching is difficult. To realize small-deformation catching, we used high-speed sensor-based (vision and proximity) control modules without a deformation model of the soft objects. A high-speed vision-based controller adjusts the positions of the fingertips of a robot to some extent. As the distance to the object decreased, the fingertip positions were accurately controlled by the high-speed, high-precision proximity-based control. Furthermore, the fingertips were stopped by a proximity-based contact detection before the object surface was deformed. Virtual damping control was effective in catching an object whose surface can be easily deformed by a small impact force or vibration of the fingertips, such as a paper balloon.

7 July 2016 in IEEE Robotics and Automation Letters
Verified
Journal Article
Open access
TSTaku Senoo
Taku Senoo
MKMasanori Koike
Masanori Koike
KMKenichi Murakami
Kenichi Murakami
MIMasatoshi Ishikawa
Masatoshi Ishikawa
In this study, the impedance control for smoothly receiving the impact of an incoming object is designed and realized. The control strategy is based on the idea that the back drive motion of an end effector attributable to the collision impact is regarded as plastic deformation of the robot. The impedance dynamics are constructed from the Maxwell model, which describes plastic deformation. Next, two types of control methods are proposed in terms of the connection configuration of the spring and damper. Physical simulations of the impact absorption with a robotic arm are executed to validate and analyze the proposed control laws.

6 March 2024 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
NZNan Zhao
Nan Zhao
KMKenichi Murakami
Kenichi Murakami
YYYuji Yamakawa
Yuji Yamakawa
This study aims to enhance the flexibility of robots in the manufacturing process to meet the growing demand for flexible manufacturing systems by constructing a dynamic compensation system. The system enables the end effector of the robot to track the trajectory contour on the horizontal plane, even if there is a deviation between the teaching trajectory and the target trajectory contour. The proposed system employs an innovative mechanism design and algorithm that enables dynamic compensation of the robot’s absolute position in the XY-plane, even when the end effector is obstructed. The system uses an XY-stage and two industrial cameras, with each axis being separately controlled. To detect and compensate for errors in the end effector and target trajectory, the two cameras are aligned with the X- and Y-direction linear stage, respectively. The cameras are fixed with respect to the linear stage, and the end effector is placed on the stage work surface. Unlike traditional stereo cameras, the cameras in this system do not require calibration for their positional relationship. To verify the system’s effectiveness, this study set a group of teaching and target trajectory contours with a maximum deviation of over than 8 mm. Under the compensation of the system, the maximum error between the end effector and the target trajectory contour was 22.8 pixels (1.34 mm), with an average absolute error of 5.4 pixels (0.32 mm). Compared to the maximum error of 8.45 mm before compensation, the error has been reduced by 84 %.

1 January 2016 in Journal of Physical Therapy Science
Verified
Journal Article
Open access
HFHiroyuki Fujisawa
Hiroyuki Fujisawa
HSHiroto Suzuki
Hiroto Suzuki
SKShingo Kawakami
Shingo Kawakami
KMKenichi Murakami
Kenichi Murakami
MSMakoto Suzuki
Makoto Suzuki
[Purpose] The purpose of the present study was to examine the validity of functional reach models by comparing actual values with estimated values. [Subjects and Methods] Twenty-eight volunteers were included in this study (male: 14, female: 14, age: 21 ± 1 years, height: 166.8 ± 9.0 cm, and body mass: 60.1 ± 8.5 kg). The maximum forward fingertip position and joint angles were measured using the original equipment. In addition, the maximum forward fingertip position, shoulder joint angle, and knee or ankle joint angle were estimated using the functional reach model. [Results] The correlation coefficients between actual data and estimated data for the maximum forward fingertip position, shoulder joint angle, and ankle joint angle while standing were 0.93, 0.83, and 0.73, respectively. The correlation coefficients between actual data and estimated data for the maximum forward fingertip position, shoulder joint angle, and knee joint angle while kneeling were 0.86, 0.81, and 0.72, respectively. [Conclusion] The validity of both functional reach models in estimating optimal posture was confirmed. Therefore, the functional reach model is useful for evaluation of postural control and optimal postural control exercises.

20 October 2022 in Journal of Robotics and Mechatronics
Verified
Journal Article
Open access
KMKenichi Murakami
Kenichi Murakami
SHShouren Huang
Shouren Huang
MIMasatoshi Ishikawa
Masatoshi Ishikawa
YYYuji Yamakawa
Yuji Yamakawa
Title: Fully Automated Bead Art Assembly for Smart Manufacturing Using Dynamic Compensation Approach | Keywords: robotic automation, dynamic compensation, high-speed vision | Author: Kenichi Murakami, Shouren Huang, Masatoshi Ishikawa, and Yuji Yamakawa

16 September 2020 in Robotics
Verified
Journal Article
Open access
PDF file
KMKenichi Murakami
Kenichi Murakami
KIKoki Ishimoto
Koki Ishimoto
TSTaku Senoo
Taku Senoo
MIMasatoshi Ishikawa
Masatoshi Ishikawa
In recent years, force control has become more important due to the physical interaction of robots with humans and applications of robots to complex environments. Impedance control is widely used in force control; however, it cannot reproduce the behavior of plastic deformation because it returns to the initial position when the force is removed, similar to elastic deformation. On the other hand, Senoo et al. have proposed plastic deformation control based on the Maxwell model. However, because plastic deformation control is model-based, it is subject to the modeling and parameter errors of the controlled system. A robot hand is relatively small and lightweight; because it uses a gearbox with a high reduction ratio for its joints, it is significantly affected by friction and tends to deviate strongly from the desired motion. Therefore, in this study, a method that is robust against modeling and parameter errors is proposed by feeding back the error from the desired trajectory with the inner position loop. Then, the effectiveness of the proposed method is shown through simulations and experiments using an actual robotic system.