Frederick Pessu

Dr. Frederick Pessu

Institute of Functional Surfaces, School of Mechanical Engineering, University of Leeds, Leeds, LS2 9JT, UK

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 July 2017 in Corrosion
Verified
Journal Article
Closed access
Frederick PessuFrederick Pessu
Frederick Pessu
Richard BarkerRichard Barker
Richard Barker
ANAnne Neville
Anne Neville
Localized corrosion of carbon steel pipelines in oilfield environments is a serious concern. In environments containing both CO2 and H2S gases, pitting corrosion of carbon steel is considered to be a common occurrence which is particularly complex and still not fully understood. This paper presents a parametric study investigating the pitting corrosion behavior of carbon steel in CO2-H2S-containing environments. The work presented is divided into two parts. Part one focuses on understanding the impact of changes in three key process parameters (namely: temperature, absence/presence of 10% H2S, and absence/presence of CO2 in the gas phase) on FeS film formation process and overall the corrosion behavior of carbon steel with emphasis on general corrosion of carbon steel in a 3.5 wt% NaCl brine at 30°C and 80°C. Part two focuses on understanding the early and later stages of the pitting corrosion process, with consideration afforded to general corrosion and iron sulfide (FeS) film formation mechanisms, kinetics, and characteristics. The experiments were conducted based on short-term (7 h) and long-term tests (168 h) to investigate the early and later stages of evolution of pitting corrosion. Corrosion film properties and morphology are studied through a combination of electrochemical and surface analysis techniques which include scanning electron microscopy and x-ray diffraction. The extent of corrosion damage of the carbon steel is evaluated through the implementation of surface interferometry to study pit depth and geometry. The results show that early stages of pitting corrosion are more likely to occur with the formation of mackinawite at both 30°C and 80°C in H2S systems than in CO2 systems after 7 h. However, at 80°C extensive uniform corrosion is dominant, leading to the competing effect of iron sulfide (FeS) formation, continuous evolution of pitting corrosion, and continuous ferrite dissolution in the presence of CO2. Results from 168 h tests showed a buildup of FeS on the corroding steel surface with time with the increase in temperature and presence of CO2 in the gas phase. The buildup of FeS in H2S-CO2-containing environments is enhanced by ferrite dissolution. The FeS formed after 168 h is composed mainly of mackinawite at 30°C, and mackinawite and pyrrhotite at 80°C after 168 h. The combination of mackinawite (with a different morphology) and pyrrhotite is shown to promote more pitting and localized corrosion at 80°C than for mackinawite alone at 30°C.

31 March 2018 in Corrosion
Verified
Journal Article
Closed access
Frederick PessuFrederick Pessu
Frederick Pessu
YHYong Hua
Yong Hua
RBRichard Barker
Richard Barker
ANAnne Neville
Anne Neville
There have been increasing concerns related to the challenges posed by hydrogen sulfide (H2S) corrosion to the integrity of oilfield pipeline steels. In environments containing variable quantities of both carbon dioxide (CO2) and H2S gas, the corrosion behavior of carbon steel can be particularly complex. There is still no universal understanding of the changes in the mechanisms, sequence of electrochemical reactions and impact on the integrity of carbon steel materials as a result of changes in H2S-CO2 gas ratio. The film formation process, film characteristics, and morphology in CO2- and H2S-containing systems are also known to be different depending upon the environmental and physical conditions and this influences the rates of both general and pitting corrosion. Questions still remain as to how the combined presence of CO2 and H2S gases at different partial pressure ratios influence the corrosion mechanisms, as well as initiation and propagation of surface pits. This paper presents an investigation into the overall (i.e., general and pitting) corrosion behavior of carbon steel in CO2-H2S-containing environments. The work explores the impact of changes in ratios of CO2 and H2S partial pressures at both 30°C and 80°C in a 3.5 wt% NaCl solution. All experiments are performed at atmospheric pressure, while H2S gas content is varied at 0 ppm (0 mol%), 100 ppm (0.01 mol%), 1,000 ppm (0.1 mol%), 10,000 ppm (1 mol%), and 100,000 ppm (10 mol%) in H2S-CO2 corrosion environments. Corrosion film properties and morphology are studied through a combination of scanning electron microscopy and x-ray diffraction. The results show that the morphology and composition of iron sulfide formed changes with H2S gas concentration because of the continuous interaction of the corrosion interface with the corrosion media even in the presence of initially formed FeS (mainly mackinawite). This often leads to the formation of a different morphology of mackinawite as well as different polymorphs of FeS. This also has the impact of either increasing or decreasing the uniform corrosion rate at low and higher concentration of H2S gas depending on the temperature. Pitting corrosion is also evaluated after 168 h to determine the impact of increasing H2S content on the extent and morphology of pitting corrosion attack. The results from the pitting corrosion investigation show that increased and severe pitting corrosion attack occurs at higher H2S concentration and temperature. The morphology of pitting corrosion attack is also linked to the changes in the H2S content with an indication of a critical concentration range at which the nature of attack changes from narrow and small diameter pits to severe localized attack. The critical concentration threshold for such transition is shown in this study to reduce with increasing temperature.

1 December 2021 in Journal of Petroleum Science and Engineering
Verified
Journal Article
Closed access
Frederick PessuFrederick Pessu
Frederick Pessu
RBRichard Barker
Richard Barker
FCFakuen Chang
Fakuen Chang
TCTao Chen
Tao Chen
ANAnne Neville
Anne Neville

18 October 2022 in Results in Engineering
Verified
Journal Article
Open access
Frederick PessuFrederick Pessu
Frederick Pessu
ESEman Saleem
Eman Saleem
CECayetano Espejo
Cayetano Espejo
ANAnne Neville
Anne Neville


6 August 2020 in Corrosion
Verified
Journal Article
Closed access
Frederick PessuFrederick Pessu
Frederick Pessu
RBRichard Barker
Richard Barker
ANAnne Neville
Anne Neville
This paper investigates the synergy of chloride ion concentration and temperature on the general and pitting corrosion of carbon steel in CO2-saturated environments. Experiments were conducted over 168 h in different concentrations of NaCl brines (1 wt%, 3.5 wt%, and 10 wt%) and temperatures (30°C, 50°C, and 80°C) with the aim of elucidating the combined effect of changes in chloride ion concentration and temperature on overall metal degradation, taking into consideration general and pitting corrosion. This also includes a correlation with the formation and properties of FeCO3 corrosion products. Linear polarization resistance was implemented to monitor the electrochemical responses. Corrosion product characteristics and morphologies were studied through a combination of scanning electron microscopy and x-ray diffraction. Pitting corrosion evaluation was conducted through the application of 3D surface profilometry to study pit geometries such as the depth and diameter. The results show that general and pitting corrosion are strongly correlated to the synergistic effects of changing chloride ion concentration and temperature in carbon steel as a result of their combined influence on ferrite (Fe) dissolution and FeCO3 formation. This represents a paradigm shift from the already established mechanisms on chloride ion and temperature effects on passive alloys such as stainless steel. Increasing chloride ion concentration and temperature up to 10 wt% NaCl and 50°C to 80°C, respectively, is observed to increase the rate of Fe dissolution and formation of semiprotective FeCO3 corrosion products, leading to the increased manifestation and severity of pitting corrosion. The results also show that a “threshold chloride concentration” exists at 30°C, above which there is no significant increase in corrosion rate. However, such “threshold effects” were not observed at higher temperatures evaluated in the range of chloride concentration considered in this study.