The purification of used oils and their introduction into production cycles lead to reduction in environmental contamination. A simulation was conducted to study the thermal degradation of sunflower oil under varying temperatures over time. In the purification process of used cooking oil, an adsorption technique using zeolite and eggshell as an adsorbent (5, 10, 20, and 30 g/100 mL used oil) was applied. To optimize purification, different doses of thermally and chemically activated adsorbents were used, at different temperatures (30 and 80 °C). Therefore, this study was conducted in batch operations to determine the effect of suitable adsorption for a contact time of the adsorbent of 2 h. In comparison, the purification of used vegetable oils was achieved using a saline solution. The adsorption capacity was evaluated by determining the physicochemical parameters of the oils before and after purification. The characterization of natural adsorbents was carried out using scanning electron microscopy (SEM) and X-ray fluorescence spectrometry (XRF). The results showed that the adsorbent in a dose of 30 g of zeolite activated with NaOH and heat-treated eggshell, respectively, exhibited a larger surface area and greater adsorption capacity. Adsorption increased with contact time. The FT-IR spectra of the oils showed the IR bands at 1097, 1160, and 1237, corresponding to the presence of the ester C-O-, 1743 for C=O ester, 2853, 2922 for (CH₂, CH₃), and 3008 for (C=C). The acidity and peroxide values decreased with increasing dose and contact time with zeolite or eggshell. Together, our result strongly suggests that natural adsorbents contribute to the purification of used oils.

The dissolution of the main metals (Cu, Zn, Sn, Pb and Fe) found in waste printed circuit boards (WPCBs) was investigated by electrochemical corrosion measurements (potentiodynamic polarization and electrochemical impedance spectroscopy (EIS)) in different bromide-based systems that could be used as lixiviants in hydrometallurgical route of metals recovery. The analysis of the corrosion products was carried out by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) measurements. All measurements showed that the addition of bromine in the electrolyte favors to great extents the dissolution process of all studied metals as compared to bromine-free electrolytes. In the investigated experimental conditions, the highest dissolution rates of the metals were obtained in acidic KBr solution containing 0.01 mol/L bromine and they decreased in the following order: Zn >> Sn > Pb > Fe > Cu. The XRD and XPS chemical assessment allowed the identification of the dissolution products formed on the metallic surfaces after exposure to the electrolytes. They consisted mainly of oxides in the case of Cu, Zn, Sn and Fe, while the presence of PbBr₂ was also noticed on the lead surface. Based on the results of EIS and surface investigations, several models explaining the corrosion behavior of the metals were proposed and discussed. The obtained results demonstrate that all studied metals could be successfully leached using brominated solutions, providing a viable alternative for the selective and efficient recovery of the base metals from WPCBs through a multi-step hydrometallurgical processing route.

In recent years, the concept of reusing expired pharmaceuticals as corrosion inhibitors has attracted considerable attention due to the increasing demand for sustainable and eco-friendly solutions. This paper investigates the potential of an expired drug, called Fluimucil, containing N-acetylcysteine (NAC, 300 mg/3 mL), as a green corrosion inhibitor of bronze exposed to 3.5 wt.% NaCl solution and simulated acid rain (pH = 3.4). Potentiodynamic polarization measurements revealed that the drug acted mainly as a cathodic-type inhibitor in both electrolytes. Inhibition efficiency increased with drug concentration, reaching the maximum values of 86.7% in the presence of 36 mM NAC in the saline solution and 90.2% in the presence of 6 mM NAC in simulated acid rain. The anticorrosive effect of the drug was likely due to the adsorption of NAC on the bronze surface, which hindered to some extent the charge transfer reaction and corrosion product formation, thereby offering enhanced protection. Disregarding the nature of the corrosive electrolyte, NAC adsorption on the bronze followed the Langmuir isotherm model, involving a combination of physisorption and chemisorption processes. Surface examination by SEM-EDX confirmed that expired Fluimucil significantly mitigated the surface degradation and the corrosion products on the bronze.

The study evaluated the impact of graphene powders used as additives in the recipe of the experimental lime mortar to a mixture ratio of 1:2.5 of NHL3.5 hydraulic lime:fine sand. The content of binder, aggregate and water was kept constant, varying only the amount and the type of the added additives in relation to the amount of natural hydraulic lime NHL3.5. The following five types of experimental mortars were prepared as follows: reference mortar (without additive); mortars containing 1 wt.% GO and 5 wt.% GO powder; mortar with the following GO powders mixture: GO powder functionalized with silver nanoparticles and with fly ash (GO-Ag + GO-fly ash); mortar with the following GO powders mixture: GO with zinc oxide and with titanium oxide (GO-ZnO + GO-TiO₂). The influence of the GO-based additive addition on the porosity, surface microstructure, and water sorption coefficient of the mortar samples was evaluated. The antibacterial effect of the mortar samples against three bacterial strains was also investigated. The best results were obtained for the experimental mortar containing GO-ZnO -TiO_2, which showed improved experimental properties that potentially allow its use for the rehabilitation of heritage buildings.