Curing by CO2 is a way to utilize CO2 to reduce greenhouse gas emissions. Placing early-age cement paste in a CO2 chamber or pressure vessel accelerates its strength development. Cement carbonation is attributed to the quickened strength development, and CO2 uptake can be quantitatively evaluated by measuring CO2 gas pressure loss in the pressure vessel. A decrease in CO2 gas pressure is observed with all cement pastes and mortar samples regardless of the mix proportion and the casting method; one method involves compacting a low water-to-cement ratio mix, and the other method comprises a normal mix consolidated in a mold. The efficiency of the CO2 curing is superior when a 20% concentration of CO2 gas is supplied at a relative humidity of 75%. CO2 uptake in specimens with the same CO2 curing condition is different for each specimen size. As the specimen scale is larger, the depth of carbonation is smaller. Incorporating colloidal silica enhances the carbonation as well as the hydration of cement, which results in contributing to the increase in the 28-day strength.
1 June 2021 in Construction and Building Materials
The effect of CO2 curing on alkali-activated slag paste activated by a mixture of sodium hydroxide and sodium silicate solutions is reported in this paper. The paste samples after demolding were cured in three different curing environments as follows: (1) environmental chamber maintained at 85% relative humidity (RH) and 25 °C; (2) 3-bar CO2 pressure vessel; and (3) CO2 chamber maintained at 20% CO2 concentration, 70% RH and 25 °C. The hardened samples were then subjected to compressive strength measurement, X-ray diffraction analysis, and thermogravimetry. All curing conditions used in this study were beneficial for the strength development of the alkali-activated slag paste samples. Among the curing environments, the 20% CO2 chamber was the most effective on compressive strength development; this is attributed to the simultaneous supply of moisture and CO2 within the chamber. The results of X-ray diffraction and thermogravimetry show that the alkali-activated slag cured in the 20% CO2 chamber received a higher amount of calcium silicate hydrate (C-S-H), while calcite formed at an early age was consumed with time. C-S-H was formed by associating the calcite generated by CO2 curing with the silica gel dissolved from alkali-activated slag.
This study investigated the rheological and mechanical properties of cement composites with kenaf and jute fibers for use in shotcrete. The length and volume fractions of the fiber were varied; the rheological properties were analyzed in terms of air content, compression and flexural tests were conducted, and the degree of fiber dispersion was assessed using fluorescence microscopy. The rougher surfaces of the jute fibers led to a higher yield stress and viscosity of the composite compared to the kenaf fibers. The use of 10-mm-long jute fibers at 2.0% volume fraction led to optimal rheological properties while 30-mm-long jute fibers at 1.0% resulted in the worst properties. The yield stress and plastic viscosity exhibited positive and negative correlations with the fiber volume fraction, respectively. This was likely because of the bridging and fluid actions of the bubbles at higher fiber content. For a given fiber content, only the yield stress increases with an increase in fiber length. Although all the mechanical properties deteriorated (compressive strength decreased from 27.5 to 6 MPa, and flexural strength deteriorated from 6.2 to 1.8 MPa), the mixtures failed in a ductile manner. Using 10-mm-long kenaf fibers at 2.0% induced optimal fiber dispersion, whereas the minimum dispersion-coefficient value was found for 5-mm-long kenaf fibers at 0.5%.
19 January 2023 in International Journal of Concrete Structures and Materials
This study investigated the efficiency of CO2 curing in blast-furnace slag pastes activated with three concentrations of KOH solution (3, 4, and 5 M). The CO2 curing was applied into the alkali-activated slag paste for 3 days. The CO2-cured pastes were subjected to subsequent curing in a water bath or exposed to seawater. The mechanical properties and characteristics of the reaction products were compared. Full strength can be obtained within 3 days of the early CO2 curing. The strength remained almost constant regardless of the activator concentration. The CO2-cured samples produced more CaCO3 after exposure to the seawater. The carbonates filled the micropores of the samples, and no strength reduction was observed. The hydrates Ca(OH)2 and C–S–H(I) are carbonated, forming calcite and amorphous CaCO3 during the subsequent curing and exposure to seawater as well as the CO2 curing. A less dense matrix with a lower activator concentration facilitated the diffusion of CO2 and promoted early carbonation in the paste. The polymerization of C–S–H(I) was relatively slow with low activity, and within the period of CO2 curing, more carbonates were produced in the sample prepared at a low activator concentration.