Epithelial cell function is modulated by mechanical forces imparted by the extracellular environment. The transmission of forces onto the cytoskeleton by modalities such as mechanical stress and matrix stiffness is necessary to address by the development of new experimental models that permit finely tuned cell mechanical challenges. Herein, we developed an epithelial tissue culture model, named the 3D Oral Epi-mucosa platform, to investigate the role mechanical cues in the epithelial barrier. In this platform, low-level mechanical stress (0.1 kPa) is applied to oral keratinocytes, which lie on 3D fibrous collagen (Col) gels whose stiffness is modulated by different concentrations or the addition of other factors such as fibronectin (FN). Our results show that cells lying on intermediate Col (3 mg/mL; stiffness = 30 Pa) demonstrated lower epithelial leakiness compared with soft Col (1.5 mg/mL; stiffness = 10 Pa) and stiff Col (6 mg/mL; stiffness = 120 Pa) gels, indicating that stiffness modulates barrier function. In addition, the presence of FN reversed the barrier integrity by inhibiting the interepithelial interaction via E-cadherin and Zonula occludens-1. Overall, the 3D Oral Epi-mucosa platform, as a new in vitro system, will be utilized to identify new mechanisms and develop future targets involved in mucosal diseases.

Insulator based dielectrophoresis (iDEP) is becoming increasingly important in emerging biomolecular applications, including particle purification, fractionation, and separation. Compared to conventional electrode-based dielectrophoresis (eDEP) techniques, iDEP has been demonstrated to have a higher degree of selectivity of biological samples while also being less biologically intrusive. Over the past two decades, substantial technological advances have been made, enabling iDEP to be applied from micro, to nano and molecular scales. Soft particles, including cell organelles, viruses, proteins, and nucleic acids, have been manipulated using iDEP, enabling the exploration of subnanometer biological interactions. Recent investigations using this technique have demonstrated a wide range of applications, including biomarker screening, protein folding analysis, and molecular sensing. Here, we review current state-of-art research on iDEP systems and highlight potential future work.

Biofabrication has been adapted in engineering patient-specific biosynthetic grafts for bone regeneration. Herein, we developed a three-dimensional (3D) high-resolution, room-temperature printing approach to fabricate osteoconductive scaffolds using calcium phosphate cement (CPC). The non-aqueous CPC bioinks were composed of tetracalcium phosphate, dicalcium phosphate anhydrous, and Polyvinyl butyral (PVB) dissolved in either ethanol (EtOH) or tetrahydrofuran (THF). They were printed in an aqueous sodium phosphate bath, which performs as a hardening accelerator for hydroxyapatite formation and as a retainer for 3D microstructure. The PVB solvents, EtOH or THF, affected differently the slurry rheological properties, scaffold microstructure, mechanical properties, and osteoconductivity. Our proposed approach overcomes limitations of conventional fabrication methods, which require high-temperature (>50 °C), low-resolution (>400 μm) printing with an inadequate amount of large ceramic particles (>35 μm). This proof-of-concept study opens venues in engineering high-resolution, implantable, and osteoconductive scaffolds with predetermined properties for bone regeneration.

For poly(p-phenylene biphenyltetracarboximide) (BPDA-PDA) and poly(4,4′-oxydiphenylene pyromellitimide) (PMDA-ODA) in films, surface topographies and molecular in-plane orientations were very sensitive to the precursor origins as well as the softbake and imidization processes. Poly(amic diethyl ester) precursor produced higher surface roughness and lower molecular in-plane orientation in the resultant polyimide than the corresponding poly(amic acid). Rapid softbake and imidization process caused relatively high surface roughness and low molecular in-plane orientation in the resultant film. Rougher surface in the film was more favorably rubbed by rubbing process, causing higher pretilt angle in liquid-crystal molecules in contact with the rubbed film.

Electrocorticography (ECoG) is a conventional, invasive technique for recording brain signals from the cortical surface using an array of electrodes. In this study, we developed a highly flexible 22-channel ECoG microelectrode array on a thin Parylene film using novel fabrication techniques. Narrow (<40 µm) and thin (<500 nm) microelectrode patterns were first printed on PDMS, then the patterns were transferred onto Parylene films via vapor deposition and peeling. A custom-designed, 3D-printed connector was built and assembled with the Parylene-based flexible ECoG microelectrode array without soldering. The impedance of the assembled ECoG electrode array was measured in vitro by electrochemical impedance spectroscopy, and the result was consistent. In addition, we conducted in vivo studies by implanting the flexible ECoG sensor in a rat and successfully recording brain signals.

Orthopedic and craniofacial surgical procedures require the reconstruction of bone defects caused by trauma, diseases, and tumor resection. Successful bone restoration entails the development and use of bone grafts with structural, functional, and biological features similar to native tissues. Herein, we developed three-dimensional (3D) printed fine-tuned hydroxyapatite (HA) biomimetic bone structures, which can be applied as grafts, by using calcium phosphate cement (CPC) bioink, which is composed of tetracalcium phosphate (TTCP), dicalcium phosphate anhydrous (DCPA), and a liquid [Polyvinyl butyral (PVB) dissolved in ethanol (EtOH)]. The ink was ejected through a high-resolution syringe nozzle (210 µm) at room temperature into three different concentrations (0.01, 0.1, and 0.5) mol/L of the aqueous sodium phosphate dibasic (Na₂HPO₄) bath that serves as a hardening accelerator for HA formation. Raman spectrometer, X-ray diffraction (XRD), and scanning electron microscopy (SEM) demonstrated the real-time HA formation in (0.01, 0.1, and 0.5) mol/L Na₂HPO₄ baths. Under those conditions_, HA was formed at different amounts, which tuned the scaffolds’ mechanical properties, porosity, and osteoclast activity. Overall, this method may pave the way to engineer 3D bone scaffolds with controlled HA composition and pre-defined properties, which will enhance graft-host integration in various anatomic locations.