This paper introduces an innovative thermal modeling technique which accurately predicts the winding temperature of electrical machines, both at transient and steady state conditions, for applications where the stator Joule losses are the dominant heat source. The model is an advanced variation of the classical lumped-parameter thermal network approach, with the expected degree of accuracy but at a much lower computational cost. A seven-node thermal network is first implemented and an empirical procedure to fine-tuning the critical parameters is proposed. The derivation of the low computational cost model from the thermal network is thoroughly explained. A simplification of the seven-node thermal network with an equivalent three-node thermal network is then implemented, and the same procedure is applied to the new network for deriving an even faster low computational cost model. The proposed model is then validated against experimental results carried on a permanent magnet synchronous machine which is part of an electro-mechanical actuator designed for an aerospace application. A comparison between the performance of the classical lumped-parameter thermal network and the proposed model is carried out, both in terms of accuracy of the stator temperature prediction and of the computational time required.
13 November 2017 in IEEE Transactions on Industrial Electronics
The power density of electrical machines for transport applications has become a critical aspect and target of optimization. This paper looks at the development of an intelligent, rapid, flexible, and multidomain tool to aid for system-level optimization of electrical machines within next-generation high power density applications. The electromagnetic, thermal, and mechanical aspects are wholly integrated, thus enabling the optimization including the nonactive mass. The implementation and overall architecture of the tool are described, and using a case study drawn from the aerospace industry, the tool is used to compare the power density of various surface permanent magnet topologies including single airgap and dual airgap machines, highlighting the particular suitability of the dual rotor topology in achieving the best power to mass ratio. Finally, the accuracy of the tool is highlighted by practical realization and experimental validation.
This paper proposes and investigates an analytical method for assessing the risk of potential irreversible demagnetization in the permanent magnets (PMs) of electrical machines equipped with n-stages, Halbach arrays. The higher risk of demagnetization, synonymous with Halbach arrays, imposes that the method be both load and temperature dependent. In fact, the proposed method studies the magnetic field distribution in the air gap and PM region, for various operating temperatures and expresses these fields as analytical expressions for the no-load and peak-load conditions. The model can cater for Halbach arrays with up to n stages, thus making it a versatile tool that can be utilized for various Halbach configurations. Finite-element analysis is used to validate the method. The analytical tool is then used for the design and analysis of a high torque density, outer rotor, traction motor. The motor is for an aerospace application and its operating duty cycle imposes very high, short-time, peak-load conditions at elevated temperatures, posing an elevated risk of irreversible PM demagnetization. The model is used to investigate various Halbach configurations for this application, in order to reduce the demagnetization risk and also to improve the general performance of the machine. The analytical method thus provides a computationally efficient tool that can be used to predict and prevent demagnetization in Halbach-equipped electrical machines operating in harsh environments such as the aerospace sector.
18 September 2013 in IEEE Transactions on Industrial Electronics
This paper details the design considerations of a permanent-magnet three-phase synchronous machine for fault-tolerant operation. A multidisciplinary approach to the optimal design of the machine is adopted, targeted at minimizing the additional losses resulting from faulty operating conditions and accounting for the remedial control strategy implemented. The design of a closed-slot six-slot four-pole machine is presented. The machine is prototyped and tested to validate the analytical-computational performances predicted in the design and analysis stage under healthy and faulty conditions.
4 December 2017 in IEEE Transactions on Industrial Electronics
Radial force control in electrical machines has been widely investigated for a variety of bearingless machines, as well as for the conventional structures featuring mechanical bearings. This paper takes advantage of the spatial distribution of the winding sets within the stator structure in a multisector permanent-magnet (MSPM) machine toward achieving a controllable radial force. An alternative force control technique for MSPM machines is presented. The mathematical model of the machine and the theoretical investigation of the force production principle are provided. A novel force control methodology based on the minimization of the copper losses is described and adopted to calculate the d-q axis current references. The predicted performances of the considered machine are benchmarked against finite-element analysis. The experimental validation of the proposed control strategy is presented, focusing on the suppression of selected vibration frequencies for different rotational speeds.
22 March 2019 in IEEE Transactions on Industrial Electronics
This paper deals with the design, prototyping, and testing of a high-speed permanent magnet generator with amorphous alloy magnetic core for aerospace applications. The target operative speed range is 30,000-60,000 rpm with an output power range between 50 kW and 300 kW. Two types of winding are examined and compared: tooth-coil and distributed. Special attention is dedicated to the rotor dynamics aspects of the solid disk magnet rotor assembly. The multidisciplinary design process is described. Electromagnetic calculations are provided for different operative conditions, where the magnetic field and losses distribution are determined. Based on the initial calculations and analysis, a full-size prototype rated at 120 kW and 60,000 rpm rotational speed featuring a stator core made from an amorphous alloy was developed and tested. The tests result proved the high efficiency achievable with the adopted and described technical solutions. It has been proved that the use of amorphous alloy in high-speed electric machines enables to minimize losses in the stator magnetic core by 5-7 times in comparison with traditional materials.