Raul Figueroa

Dr. Raul Figueroa

Department of Materials Engineering, Applied Mechanics and Construction, University of Vigo, Vigo, Spain
orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2015 in Applied Surface Science
Verified
Journal Article
Closed access
CFCarmen Mª Abreu Fernández
Carmen Mª Abreu Fernández
MCMaría Julia Cristóbal
María Julia Cristóbal
Raul FigueroaRaul Figueroa
Raul Figueroa
Gloria PenaGloria Pena
Gloria Pena

31 December 2005 in Spectrochimica Acta Part B: Atomic Spectroscopy
Verified
Journal Article
Closed access
Raul FigueroaRaul Figueroa
Raul Figueroa
MGMónica García
Mónica García
ILIsela Lavilla
Isela Lavilla
CBCarlos Bendicho
Carlos Bendicho


1 January 2012 in Corrosion Science
Verified
Journal Article
Closed access
CFCarmen Mª Abreu Fernández
Carmen Mª Abreu Fernández
MCMaría Julia Cristóbal
María Julia Cristóbal
Raul FigueroaRaul Figueroa
Raul Figueroa
Gloria PenaGloria Pena
Gloria Pena

12 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
ACAntonio Collazo
Antonio Collazo
Raul FigueroaRaul Figueroa
Raul Figueroa
Carmen PérezCarmen Pérez
Carmen Pérez
X. Ramón NóvoaX. Ramón Nóvoa
X. Ramón Nóvoa
In this work, the corrosion properties of 316L stainless steel (SS) obtained by selective laser melting (SLM) are analyzed. The electrochemical results of samples manufactured with an energy density between 40 and 140 J/mm3 are compared using different hatch distances and laser speeds. The analysis correlates the impact of the microstructure and processing defects of SLM 316L stainless steel on its behavior against corrosion. The optimal manufacturing conditions were selected considering the electrochemical results. Although the samples obtained with an energy density close to 90 J/mm3 show a high resistance to corrosion, their performance depends on the combination of selected parameters, obtaining the best results for an intermediate laser speed and a low hatch distance. These manufacturing conditions produce a higher breakdown potential, a faster repassivation of the steel and reduce the current density on electrochemical test.

3 May 2006 in Journal of Analytical Atomic Spectrometry
Verified
Journal Article
Closed access
PDF file
MGM. García
M. García
Raul FigueroaRaul Figueroa
Raul Figueroa
ILI. Lavilla
I. Lavilla
CBC. Bendicho
C. Bendicho
A flow-through UV reactor has been implemented in an automated flow-injection/stopped-flow manifold, and used for on-line generation of Se volatile derivatives prior to detection by quartz furnace atomic absorption spectrometry. The presence of a low molecular weight organic acid (formic or acetic) in the carrier was a necessary requirement so that efficient vapour generation was achieved. Stopped-flow conditions were employed with the aim of increasing the time for which the sample zone was subjected to UV irradiation while it was transported to the detector. The simultaneous formation of H2 during the photochemical decomposition of formic acid facilitated the atomization of the Se derivatives in the quartz furnace, and therefore the addition of H2 to the carrier gas, which is necessary for efficient atomisation, could be eliminated. Nevertheless, the presence of H2 in the carrier gas (Ar) was required for efficient atomisation when using acetic acid as carrier. This manifold allowed a sample throughput of 26 h−1 with a detection limit of 0.5 ng mL−1 Se and a repeatability, expressed as relative standard deviation, of 4%. Effect of concomitants in the online generation of Se vapours with the new manifold was investigated. Chloride salts of alkaline and alkaline-earth elements did not interfere at concentrations up to 10 000 mg L−1, but nitrate salts caused a positive effect. Tolerance of typical hydride-forming elements such as As and Sn was much higher with UV vapour generation as compared to chemical hydride generation. The presence of Cu(II) was critical since interference effects are observed from 0.05 mg L−1, but tolerance of Ni(II) was greater with UV vapour generation.