Jia-xin Gao

Dr. Jia-xin Gao

Jilin University

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 April 2021 in Metals
Verified
Journal Article
Open access
PDF file
XZXi Zhang
Xi Zhang
QCQing-Min Chen
Qing-Min Chen
JGJia-xin Gao
Jia-xin Gao
MWmingwei wang
mingwei wang
YZYa Zhang
Ya Zhang
ZCZhong-Yi Cai
Zhong-Yi Cai
This paper presents a numerical investigation on the plastic forming of doubly curved surfaces of aluminum foam sandwich panel (AFSP). A mesoscopic 3D Voronoi model that can describe the structure of closed-cell aluminum foam relatively realistically was established, and a series of numerical simulations using the model of the sandwich panel with a Voronoi foam core were conducted on the plastic forming of two typical doubly curved surfaces including spherical and saddle-shaped surfaces of AFSPs to analyze the deformation behaviors and the forming defects in detail. Multi-point forming experiments of spherical and saddle-shaped AFSPs with different target radii were implemented and the doubly curved panels with good forming quality were obtained. The simulated results of the surface illumination maps, the face sheet profiles, and the maximum strain differences in selected areas of the face sheet and the experimental results indicated that the Voronoi AFSP model can reflect the actual defects occurred in the plastic forming of doubly curved sandwich panels, and the high forming accuracy of the sandwich panel model was also demonstrated in terms of the shape error and the thickness variation.

26 December 2022 in Metals
Verified
Journal Article
Open access
PDF file
WZWeiGuang Zhang
WeiGuang Zhang
ZCZhong-Yi Cai
Zhong-Yi Cai
XZXi Zhang
Xi Zhang
JGJia-xin Gao
Jia-xin Gao
MWmingwei wang
mingwei wang
QCQing-Min Chen
Qing-Min Chen
The surface quality of an aluminum foam sandwich panel (AFSP) is very important for its appearance and application. This paper mainly studies the surface quality of AFSP after plastic forming. Combined with three-dimensional (3D) scanning technology, the normal deviation between the experimental AFSP and the target surface was obtained, and the surface quality parameters Sq, Sz and dmax were calculated to evaluate surface quality. The AFSP models with cubic-spherical (CS) and tetrakaidecahedral (TKD) as foam structures were established respectively. A series of numerical simulations of multi-point forming (MPF) were then carried out. Equivalent strain and deformation characteristics of spherical and saddle-shaped AFSP were discussed. The main surface defects produced by AFSP in plastic forming, such as surface wrinkle, the local straight face effect and surface dimpling were analyzed. Finally, MPF experiments were carried out, and it was found that the numerical simulation results were significantly corresponded to the experimental AFSP in terms of the degree and distribution of normal deviation and surface quality evaluation parameters. The TKD model was more consistent with the experimental results than the CS model. Moreover, the results show that the surface quality can be improved by thicker face sheets and smaller core cell sizes.

9 September 2021 in Materials
Verified
Journal Article
Open access
PDF file
JGJia-xin Gao
Jia-xin Gao
QCQing-Min Chen
Qing-Min Chen
LSLi-Rong Sun
Li-Rong Sun
ZCZhong-Yi Cai
Zhong-Yi Cai
Continuous roll forming (CRF) is a new technology that combines continuous forming and multi-point forming to produce three-dimensional (3D) curved surfaces. Compared with other methods, the equipment of CRF is very simple, including only a pair of bendable work rolls and the corresponding shape adjustment and support assembly. By controlling the bending shapes of the upper and lower rolls and the size of the roll gap during forming, double curvature surfaces with different shapes can be produced. In this paper, a simplified expression of the exit velocity of the sheet is provided, and the formulas for the calculation of the longitudinal curvature radius are further derived. The reason for the discrepancy between the actual and predicted values of the longitudinal radius is deeply discussed from the perspective of the distribution of the exit velocity. By using the response surface methodology, the effects of the maximum compression ratio, the sheet width, the sheet thickness, and the transverse curvature radius on the longitudinal curvature radius are analyzed. Meanwhile, the correction coefficients of the predicted formulas for the positive and negative Gaussian curvature surfaces are obtained as 1.138 and 0.905, respectively. The validity and practicability of the modified formulas are verified by numerical simulations and forming experiments.

17 September 2020 in Metals
Verified
Journal Article
Open access
PDF file
JGJia-xin Gao
Jia-xin Gao
DHD.Y. He
D.Y. He
LSLi-Rong Sun
Li-Rong Sun
XZXi Zhang
Xi Zhang
ZCZhong-Yi Cai
Zhong-Yi Cai
Continuous roll forming (CRF) is a new method for the rapid forming of three-dimensional (3D) surfaces developed in recent years, and the significant advantage of CRF compared with traditional die forming is that the longitudinal dimension of the sheet metal is not limited. By controlling the curvature radius and gap shape of upper and lower bending rolls, three-dimensional parts with different shapes and sizes can be precisely formed. When the elastic deformation is ignored during the forming process, the transversal curvature radius of the three-dimensional surface is consistent with the radius of the roll gap centerline. Therefore, the calculation of longitudinal curvature radius is the key to improve the accuracy of the 3D surface in CRF. In this paper, the basic principle of CRF is described. The modified formulas for calculating the longitudinal curvature radius of convex and saddle surfaces based on the quadratic relationship between the strain and coordinates are deduced in detail, and the corresponding design method of the roll gap is derived. Furthermore, the mathematical equations of convex and saddle surfaces are given. Through numerical simulation and theoretical analysis, it is found that the relative errors of the longitudinal centerline radius are reduced from 13.67% before modification to 4.35% after modification for a convex surface and 6.81% to 0.41% for a saddle surface when the transversal curvature radius is 800 mm and the compression ratio is 5%. The experimental and measured results indicate that the shapes of formed parts are more consistent with the target parts after modification, which further proves the applicability of the modified formulas.