Chao Wang

Dr. Chao Wang

orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 January 2023 in Optics Express
Verified
Journal Article
Closed access
YWYingjie Wu
Yingjie Wu
CLChurui Li
Churui Li
CWChao Wang
Chao Wang
BJBo Jia
Bo Jia
To solve the problem of light source jitter and asymmetric 3 × 3 coupler, a phase demodulation method with the combination of an auxiliary reference interferometer and elliptic fitting algorithm is proposed, which is verified by simulation and experiment. By introducing additional phase modulation in the auxiliary reference interferometer, the parameters of the sensing arm can be calibrated in real time, which ensures the effective operation of elliptic fitting algorithm in small signal measurement. Consequently, the experiments show that the self-calibration scheme enables a higher signal to noise and distortion ratio with an average increase of 1.65 dB and 10.47 dB compared with the traditional Arctan and cross multiplication differential, respectively. Meanwhile, the self-calibration scheme can also effectively suppress the harmonic distortion, with a total harmonic distortion of -33.64 dB in the case of small signal.

9 October 2014 in Optics Letters
Verified
Journal Article
Closed access
PDF file
JLJunhai Liu
Junhai Liu
WHWenjuan Han
Wenjuan Han
XCXiaowen Chen
Xiaowen Chen
DZDegao Zhong
Degao Zhong
BTBing Teng
Bing Teng
YLYuyi Li
Yuyi Li
For the first time, and to the best of our knowledge, we report a continuous-wave (cw) laser operation of Yb:LuPO4 crystal, demonstrated at room temperature in a compact plano-concave resonator end pumped by a diode laser. 1.61 W of cw output power around 1039 nm were generated with 2.40 W of pump power at 976 nm absorbed in a 0.3 mm thick crystal, leading to an optical-to-optical efficiency of 67%, whereas the slope efficiency was 75%. Polarized absorption and emission cross-section spectra are also presented and discussed in detail.

22 September 2016 in Microwave and Optical Technology Letters
Verified
Journal Article
Closed access
PDF file
ZYZi Ye
Zi Ye
JWJian Wang
Jian Wang
CWChao Wang
Chao Wang
BJBo Jia
Bo Jia

12 March 2024 in IEEE Sensors Journal
Verified
Journal Article
Closed access
BMBo Ma
Bo Ma
RJRui Jin
Rui Jin
CLChurui Li
Churui Li
YWYingjie Wu
Yingjie Wu
CWChao Wang
Chao Wang
BJBo Jia
Bo Jia
Interferometric distributed optical fiber sensing technology has emerged as an important branch in the field of optical fiber sensors, and the research on the technology is of great significance. In this paper, a distributed optical fiber vibration sensing localization algorithm based on phase spectrum time delay estimation is proposed. The algorithm effectively overcomes the limitations in stationary periodic vibration signals localization and multiple vibration signals localization. Theoretical analysis is presented to clarify the principle of vibration localization, especially for multiple vibrations localization. Experimental verification of vibration signal localization on a 40 km optical fiber is demonstrated. The experimental results show that the localization error is less than 20 m for the single-point stationary periodic vibration signals, while less than 50 m for the instantaneous vibration signals. This algorithm achieves the simultaneous localization of multiple stationary periodic vibration signals, while also enabling the concurrent localization of both stationary periodic signals and instantaneous signals. The algorithm shows the capability of multiple vibration signals localization.

18 April 2023 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
RJRui Jin
Rui Jin
ZYZhongzheng Yuan
Zhongzheng Yuan
YWYingjie Wu
Yingjie Wu
CWChao Wang
Chao Wang
In this paper, a novel dual-wavelength wide-spectrum erbium-doped fiber ring laser (EDFRL) for optical fiber sensing system is proposed and experimentally demonstrated. The output of EDFRL is theoretically simulated and classified depending on the theoretical analysis of laser threshold condition into “excited state” and “nonexcited state”. The influence of pump wavelength, fiber laser configuration, EDF length and output coupling ratio of EDFRL is discussed. The EDFRL pumped at 1480 nm wavelength and backward-pumped mode could achieve the stable maximum wide-spectrum output power. The output power fluctuation is lower than 0.06 dB and the center wavelengths shift is less than 0.01 nm. The practicability of EDFRL in a hybrid M-Z and Sagnac interferometer optical fiber sensing system is demonstrated through the comparison of SLD and EDFRL. Consequently, the EDFRL proposed in this study is expected to replace the traditional SLD in the optical fiber interferometric sensing system at a lower cost.

8 August 2022 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
BWBinmin Wu
Binmin Wu
ZZZiyu Zhang
Ziyu Zhang
CWChao Wang
Chao Wang
ESEnming Song
Enming Song
JCJizhai Cui
Jizhai Cui
YMYongfeng Mei
Yongfeng Mei
Due to their unique structures and properties, emerging two-dimensional (2D) materials have been at the frontier of research in, e.g., materials science, physics, and engineering. Three-dimensional (3D) tubular geometry enables 2D materials unparalleled advantages for various applications, for example, wide-angle infrared photodetectors, extremely sensitive molecular sensors, and memory with high density. Furthermore, 3D tubular structures offer a promising integration platform into chips with a broad range of materials, especially 2D materials. In this Perspective, we highlight state-of-the-art methods to assemble/manufacture 2D materials into 3D tubular structures/devices via self-rolled-up or template methods. These tubular 3D devices inspire unique physical, chemical, and mechanical properties for optical microcavity, photodetector, on-chip electronics, and bubble-propelled microengines. On-chip manufacture of 3D tubular structures/devices provides great opportunity and challenge for 2D materials for More than Moore applications such as unconventional electronics, smart sensors, and miniaturized robots.