Rhamnolipids are important biosurfactants for application in bioremediation, enhanced oil recovery, pharmaceutical, and detergent industry. In this study, rhamnolipids extracted from P. aeruginosa P6 were characterized to determine their potential fields of application. Thin-layer chromatographic analysis of the produced rhamnolipids indicated the production of two homologues: mono- and di-rhamnolipids, whose structures were verified by ¹H and ¹³C nuclear magnetic resonance spectroscopy. Additionally, high performance liquid chromatography-mass spectrometry identified seven different rhamnolipid congeners, of which a significantly high proportion was di-rhamnolipids reaching 80.16%. Rha-Rha-C10-C10 was confirmed as the principal compound of the rhamnolipid mixture (24.30%). The rhamnolipids were capable of lowering surface tension of water to 36 mN/m at a critical micelle concentration of 0.2 g/L, and exhibited a great emulsifying activity (E24 = 63%). In addition, they showed excellent stability at pH ranges 4–8, NaCl concentrations up to 9% (w/v) and temperatures ranging from 20 to 100 °C and even after autoclaving. These results suggest that rhamnolipids, produced by P. aeruginosa P6 using the cheap substrate glycerol, are propitious for biotechnology use in extreme and complex environments, like oil reservoirs and hydrocarbon contaminated soil. Moreover, P. aeruginosa P6 may be considered, in its wild type form, as a promising industrial producer of di-RLs, which have superior characteristics for potential applications and offer outstanding commercial benefits.

Background: Paromomycin is a 2-deoxystreptamine aminocyclitol aminoglycoside antibiotic with broad spectrum activity against Gram-negative, Gram-positive bacteria and many protozoa. This study introduces a strategy for paromomycin production through solid-state fermentation using Streptomyces rimosus subsp. paromomycinus NRRL 2455. Solid state fermentation has gained enormous attention in the development of several products because of their numerous advantages over submerged liquid fermentation. After selecting the best solid substrate, a time course study of paromomycin production was carried out followed by optimization of environmental conditions using response surface methodology. Paromomycin yields obtained using this technique were also compared to those obtained using submerged liquid fermentation. Results: Upon screening of 6 different substrates, maximum paromomycin concentration (0.51 mg/g initial dry solids) was obtained with the cost-effective agro-industrial byproduct, corn bran, impregnated with aminoglycoside production media. Optimization of environmental conditions using D-optimal design yielded a 4.3-fold enhancement in paromomycin concentration reaching 2.21 mg/g initial dry solids at a pH of 8.5, inoculum size of 5% v/w and a temperature of 30 °C. Conclusion: Compared to submerged liquid fermentation, solid state fermentation resulted in comparable paromomycin concentrations, cost reduction of raw materials, less energy consumption and waste water discharge, which have major implications in industrial fermentation. Therefore, solid state fermentation is a promising alternative to submerged liquid fermentation for paromomycin production. To the best of our knowledge, this is the first report on the optimized paromomycin production through solid state fermentation process.

Octadecyl 3-(3,5-di-tert-butyl-4-hydroxyphenyl) propanoate (ODHP) was extracted in a previous study from the culture broth of soil isolate Alcaligenes faecalis MT332429 and showed a promising antimycotic activity. This study was aimed to formulate ODHP loaded β-cyclodextrins (CD) nanosponge (NS) hydrogel (HG) to control skin fungal ailments since nanosponges augment the retention of tested agents in the skin. Box-Behnken design was used to produce the optimized NS formulation, where entrapment efficiency percent (EE%), polydispersity index (PDI), and particle size (PS) were assigned as dependent parameters, while the independent process parameters were polyvinyl alcohol % (w/v %), polymer-linker ratio, homogenization time, and speed. The carbopol 940 hydrogel was then created by incorporating the nanosponges. The hydrogel fit Higuchi’s kinetic release model the best, according to in vitro drug release. Stability and photodegradation studies revealed that the NS-HG remained stable under tested conditions. The formulation also showed higher in vitro antifungal activity against Candida albicans compared to the control fluconazole. In vivo study showed that ODHP-NS-HG increased survival rates, wound contraction, and healing of wound gap and inhibited the inflammation process compared to the other control groups. The histopathological examinations and Masson’s trichrome staining showed improved healing and higher records of collagen deposition. Moreover, the permeability of ODHP-NS-HG was higher through rats’ skin by 1.5-folds compared to the control isoconazole 1%. Therefore, based on these results, NS-HG formulation is a potential carrier for enhanced and improved topical delivery of ODHP. Our study is a pioneering research on the development of a formulation for ODHP produced naturally from soil bacteria. Key points: • Octadecyl 3-(3,5-di-tert-butyl-4-hydroxyphenyl) propanoate was successfully formulated as a nanosponge hydrogel and statistically optimized. • The new formula exhibited in vitro good stability, drug release, and higher antifungal activity against C. albicans as compared to the fluconazole. • Ex vivo showed enhanced skin permeability, and in vivo analysis showed high antifungal activity as evidenced by measurement of various biochemical parameters and histopathological examination.