Jean-Gabriel Lacombe

Mr. Jean-Gabriel Lacombe

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 September 2020 in Micromachines
Verified
Journal Article
Open access
PDF file
APAudrey Pitaru
Audrey Pitaru
JLJean-Gabriel Lacombe
Jean-Gabriel Lacombe
MCMegan Cooke
Megan Cooke
LBLorne Beckman
Lorne Beckman
TSThomas Steffen
Thomas Steffen
Derek RosenzweigDerek Rosenzweig
Derek Rosenzweig
The current gold standard technique for treatment of anterior cruciate ligament (ACL) injury is reconstruction with autograft. These treatments have a relatively high failure and re-tear rate. To overcome this, tissue engineering and additive manufacturing are being used to explore the potential of 3D scaffolds as autograft substitutes. However, mechanically optimal polymers for this have yet to be identified. Here, we use 3D printing technology and various materials with the aim of fabricating constructs better matching the mechanical properties of the native ACL. A fused deposition modeling (FDM) 3D printer was used to microfabricate dog bone-shaped specimens from six different polymers—PLA, PETG, Lay FOMM 60, NinjaFlex, NinjaFlex-SemiFlex, and FlexiFil—at three different raster angles. The tensile mechanical properties of these polymers were determined from stress–strain curves. Our results indicate that no single material came close enough to successfully match reported mechanical properties of the native ACL. However, PLA and PETG had similar ultimate tensile strengths. Lay FOMM 60 displayed a percentage strain at failure similar to reported values for native ACL. Furthermore, raster angle had a significant impact on some mechanical properties for all of the materials except for FlexiFil. We therefore conclude that while none of these materials alone is optimal for mimicking ACL mechanical properties, there may be potential for creating a 3D-printed composite constructs to match ACL mechanical properties. Further investigations involving co-printing of stiff and elastomeric materials must be explored.

3 May 2023 in Surgeries
Verified
Journal Article
Open access
PDF file
JLJean-Gabriel Lacombe
Jean-Gabriel Lacombe
MCMegan Cooke
Megan Cooke
HPHyeree Park
Hyeree Park
SAsuliman alshammari
suliman alshammari
Rahul GawriRahul Gawri
Rahul Gawri
Derek RosenzweigDerek Rosenzweig
Derek Rosenzweig
The current gold standard technique for the treatment of anterior cruciate ligament (ACL) injury is reconstruction with a tendon autograft. These treatments have a relatively high failure and re-rupture rate and are associated with early-onset osteoarthritis, developing within two decades of injury. Furthermore, both autografting and allografting come with several drawbacks. Tissue engineering and additive manufacturing present exciting new opportunities to explore 3D scaffolds as graft substitutes. We previously showed that 3D-printed scaffolds using low-cost equipment are suitable for tissue engineering approaches to regenerative medicine. Here, we hypothesize that Lay-Fomm 60, a commercially available nanoporous elastomer, may be a viable tissue engineering candidate for an ACL graft substitute. We first printed nanoporous thermoplastic elastomer scaffolds using low-cost desktop 3D printers and determined the mechanical and morphological properties. We then tested the impact of different surface coatings on primary human ACL fibroblast adhesion, growth, and ligamentous matrix deposition in vitro. Our data suggest that poly-L-lysine-coated Lay-Fomm 60 scaffolds increased ligament fibroblast activity and matrix formation when compared to uncoated scaffolds but did not have a significant effect on cell attachment and proliferation. Therefore, uncoated 3D printed Lay-Fomm 60 scaffolds may be viable standalone scaffolds and warrant further research as ligament tissue engineering and reconstruction grafts.

10 February 2022 in bioRxiv
Verified
Preprint
Open access
PDF file
HPHyeree Park
Hyeree Park
MCMegan Cooke
Megan Cooke
JLJean-Gabriel Lacombe
Jean-Gabriel Lacombe
MWMichael H. Weber
Michael H. Weber
PMPaul A. Martineau
Paul A. Martineau
Derek RosenzweigDerek Rosenzweig
Derek Rosenzweig
The enthesis is the interfacial tissue between ligament or tendon, and bone, which connects tissues of distinctly different mechanical properties. Although ligament and enthesis injury is commonplace, the development and healing mechanisms of these tissues are yet unclear. Current models for investigating these mechanisms are primarily in vivo animal models as in vitro models have been limited. In this study, an in vitro enthesis model was developed using a modified gel aspiration-ejection (GAE) method. Continuous two-phase aligned dense collagen (ADC) hydrogels with an overlapping interface were fabricated within 2 hours. The mechanical properties of acellular two-phase ADC confirmed the continuous nature of this model, as the mechanical properties showed no significant difference compared to single-phase ADC and maintained comparable structural and mechanical characteristics of immature ligaments and unmineralized bone. Human anterior cruciate ligament (ACL) fibroblasts and human spine vertebral osteoblasts were isolated from donor tissues and were seeded to form the enthesis model. These were cultured for 14 days, at which the viability and proliferation was observed to be 85 ± 7.5% and 230 ± 52%, respectively. Histological and immunofluorescence analyses at day 14 revealed extensive cell-driven matrix remodelling, and the seeded fibroblasts and osteoblasts maintained their phenotype within their compartments of the layered co-culture model. These results demonstrate the rapid fabrication of a two-phase co-culture system that can be utilized as an in vitro model to further understand the degenerative and regenerative mechanisms within the enthesis.