Scaffolds constitute an important element in vascularized tissues and are therefore investigated for providing the desired mechanical stability and enabling vasculogenesis and angiogenesis. In this study, supplementation of hydrogels containing either MatrigelTM and rat tail collagen I (MatrigelTM/rCOL) or human collagen (hCOL) with SeaPlaqueTM agarose were analyzed with regard to construct thickness and formation and characteristics of endothelial cell (EC) networks compared to constructs without agarose. Additionally, the effect of increased rCOL content in MatrigelTM/rCOL constructs was studied. An increase of rCOL content from 1 mg/mL to 3 mg/mL resulted in an increase of construct thickness by approximately 160%. The high rCOL content, however, impaired the formation of an EC network. The supplementation of MatrigelTM/rCOL with agarose increased the thickness of the hydrogel construct by approximately 100% while supporting the formation of a stable EC network. The use of hCOL/agarose composite hydrogels led to a slight increase in the thickness of the 3D hydrogel construct and supported the formation of a multi-layered EC network compared to control constructs. Our findings suggest that agarose/collagen-based composite hydrogels are promising candidates for tissue engineering of vascularized constructs as cell viability is maintained and the formation of a stable and multi-layered EC network is supported.
Tissue engineering utilizes an interdisciplinary approach to generate constructs for the treatment and repair of diseased organs. Generation of small vessels as vascular grafts or as envisioned central vessel for vascularized constructs is still a challenge. Here, the decellularization of porcine vessels by a non‐detergent based protocol was developed and investigated. Perfusion‐decellularization with sodium hydroxide solution resulted in removal of cellular material throughout the whole length of the vessel while preserving structural and mechanical integrity. A re‐endothelialization of the retrieved matrix with human umbilical vein endothelial cells and cardiac endothelial cells was achieved through rotation‐based seeding employing a custom‐made bioreactor. A confluent monolayer was detected on the entire luminal surface. Thus, a non‐detergent‐based decellularization method allowing the re‐endothelialization of the luminal surface was developed in this study, thereby paving the way for future implementation of the resulting construct as vascular graft or as central vessel for tissue engineered constructs in need of a perfusion system with readily available anastomosis sites.
Due to its structural and functional complexity the heart imposes immense physical, physiological and electromechanical challenges on the engineering of a biological replacement. Therefore, to come closer to clinical translation, the development of a simpler biological assist device is requested. Here, we demonstrate the fabrication of tubular cardiac constructs with substantial dimensions of 6 cm in length and 11 mm in diameter by combining human induced pluripotent stem cell-derived cardiomyocytes (iPSC-CMs) and human foreskin fibroblast (hFFs) in human fibrin employing a rotating mold technology. By centrifugal forces employed in the process a cell-dense layer was generated enabling a timely functional coupling of iPSC-CMs demonstrated by a transgenic calcium sensor, rhythmic tissue contractions, and responsiveness to electrical pacing. Adjusting the degree of remodeling as a function of hFF-content and inhibition of fibrinolysis resulted in stable tissue integrity for up to 5 weeks. The rotating mold device developed in frame of this work enabled the production of tubes with clinically relevant dimensions of up to 10 cm in length and 22 mm in diameter which—in combination with advanced bioreactor technology for controlled production of functional iPSC-derivatives—paves the way towards the clinical translation of a biological cardiac assist device.
In this paper, we report on the interaction of multifunctional nanoparticles with living endothelial cells. The nanoparticles were synthesized using direct growth of gallium nitride on zinc oxide nanoparticles alloyed with iron oxide followed by core decomposition in hydrogen flow at high temperature. Using transmission electron microscopy, we demonstrate that porcine aortic endothelial cells take up GaN-based nanoparticles suspended in the growth medium. The nanoparticles are deposited in vesicles and the endothelial cells show no sign of cellular damage. Intracellular inert nanoparticles are used as guiding elements for controlled transportation or designed spatial distribution of cells in external magnetic fields.