Victor Bright

Victor Bright


Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2014 in Advanced Materials
Verified
Journal Article
Closed access
PDF file
NENathan T. Eigenfeld
Nathan T. Eigenfeld
JGJason M. Gray
Jason M. Gray
JBJoseph J. Brown
Joseph J. Brown
GSGeorge D. Skidmore
George D. Skidmore
SGSteven George
Steven George
VBVictor Bright
Victor Bright

15 May 2008 in Journal of Electronic Packaging
Verified
Journal Article
Closed access
PDF file
ALA. D. Laws
A. D. Laws
YCY. J. Chang
Y. J. Chang
VBVictor Bright
Victor Bright
YLY. C. Lee
Y. C. Lee
We report the first use of a bimetallic buckling disk as a thermal conduction switch. The disk is used to passively alter the thermal resistance of the package of a chip scale atomic clock. A vertical-cavity surface-emitting laser and a cesium vapor cell, contained in the clock, must be maintained at 70±0.1°C even under an ambient temperature variation of −40°Cto50°C. A thermal test vehicle has been developed to characterize a sample package with a thermal conduction switch. Three cases are presented for the temperature control of the test vehicle under different load placements and environmental conditions: (1) a heating load with a good conduction path to the switch in a vacuum package; (2) the same loading as in Case 1, but packaged in air; and (3) a heating load insulated from the switch, in a vacuum package. At 38°C, the switch snaps upward to reduce the package’s thermal resistance. As a result, the heating power needed to maintain a constant temperature, 63.9±0.1°C, is increased from 118to200mW for Case 1. Such a significant change of the thermal resistance demonstrates the effectiveness of the thermal switch. However, the switch becomes less effective with air filling the gap, as in Case 2, and the switch is not effective at all if the heating load does not have a good conduction path to the switch as in Case 3. The steady state response of this novel thermal conduction switch has been well characterized through experimentation and finite element analysis.

28 May 2012 in Nanotechnology
Verified
Journal Article
Closed access
ABAlicia I Baca
Alicia I Baca
JBJoseph J. Brown
Joseph J. Brown
KBKris A Bertness
Kris A Bertness
VBVictor Bright
Victor Bright
Effects of design and materials on the dielectrophoretic self-assembly of individual gallium nitride nanowires (GaN NWs) onto microfabricated electrodes have been experimentally investigated. The use of TiO(2) surface coating generated by atomic layer deposition (ALD) improves dielectrophoretic assembly yield of individual GaN nanowires on microfabricated structures by as much as 67%. With a titanium dioxide coating, individual nanowires were placed across suspended electrode pairs in 46% of tests (147 out of 320 total), versus 28% of tests (88 out of 320 total tests) that used uncoated GaN NWs. An additional result from these tests was that suspending the electrodes 2.75 μm above the substrate corresponded with up to 15.8% improvement in overall assembly yield over that of electrodes fabricated directly on the substrate.

27 December 2011 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
JBJoseph J. Brown
Joseph J. Brown
DDDmitriy A. Dikin
Dmitriy A. Dikin
RRRodney S. Ruoff
Rodney S. Ruoff
VBVictor Bright
Victor Bright
A microfabricated mechanical test platform has been designed, fabricated, and operated. This system consists of a reusable chip capable of large-displacement actuation, which interfaces to a test coupon chip compatible with synthesis conditions for many nanomaterials. Because only normal forces are used for mechanical interfacing, the two chips are not permanently connected, allowing exchange of the test coupon chips. The actuated test platform chip contains a thermal actuator driving a compliant displacement amplification transmission, and a bulk-micromachined well in which the test coupon chips may be placed and removed. The displacement amplification structure provides 40 of output displacement, extending a probe over the well and into contact with the test coupon. The test coupon contains compliant structures that are actuated by the probe from the test platform.

27 October 2017 in Journal of Applied Mechanics
Verified
Journal Article
Closed access
PDF file
JBJoseph J. Brown
Joseph J. Brown
RMRyan C. Mettler
Ryan C. Mettler
OSOmkar D. Supekar
Omkar D. Supekar
VBVictor Bright
Victor Bright