The conversion of lignocellulosic biomass to biofuel precursors has recently been a focus of intensive research due to the essential role of biofuels as transport fuels in the future. Specifically, the conversion of fructose to 5-hydroxymethylfurfural (5HMF) has gained momentum, as 5HMF is a versatile bio-based platform molecule that leads to a plethora of high-value chemicals and biofuel molecules, such as DMF. Herein, we report the use of an environmentally friendly, Brønsted acidic, deep eutectic mixture consisting of choline chloride (ChCl) and p-TSA for the dehydration of fructose to 5HMF. Unlike previous systems, the use of ChCl–p-TSA plays a dual role, as both a hydrogen bond donor (HBD) and a catalyst for the dehydration reaction, thus obviating the addition of an external acid. The reaction was examined and optimised in a batch system, where it was found that fructose was readily dehydrated to 5HMF. The best reaction conditions, with the highest 5HMF yield of 90.7%, were obtained at a temperature of 80 °C using a DES molar mixing ratio of 1 : 1 ChCl : p-TSA and feed ratio of 2.5%, and with a reaction time of one hour.
The growing use of fibre-reinforced polymers (FRPs) is driving a demand for the development of sustainable end-of-life strategies. Solvolysis, a chemical recycling method using solvents to decompose the polymer matrix, has emerged as a promising approach for reclaiming both fibres and organic compounds from FRP waste. This work provides a comprehensive overview of solvolysis techniques by discussing the environmental benefits and economic opportunities of this technology, summarising the process conditions, and evaluating the characteristics of the recovered products. The economic viability of solvolysis lies in recovering high-value components; predominantly carbon fibres from CFRPs and organic products from GFRPs, which are suitable for reuse or as a feedstock for new composites. Solvolysis can operate under low temperature and pressure (LTP) or high temperature and pressure (HTP) conditions. The choice of solvent, catalyst, reaction time, and temperature is crucial to achieving high resin decomposition while preserving fibre properties. To achieve an economically viable and environmentally beneficial process, it will be essential to optimise these parameters. A key challenge is maintaining the strength and surface properties of the recovered fibres, as degradation in their performance can limit their suitability for high-performance applications. The implication of this is that, without careful consideration of the recycling process, FRPs cannot be fully circular. They will be continuously downgraded into low-value applications and ultimately incinerated or landfilled. This review further explores the diversity of organic products obtained, which can range from monomers to oligomers to complex mixtures. Efficient separation and upgrading techniques, such as distillation and liquid–liquid extraction, are essential to maximise the value of the recovered organics. These additional processing steps are likely to result in greater financial and resource costs within a commercial recycling system. This review concludes with a summary of commercial solvent-based recycling ventures and an outlook on future research directions, which includes the need to develop processes capable of recovering high-value, long carbon fibres. Successful development of such a process would represent a step-change in the value proposition of a carbon fibre recycling industry.
Supercritical Water Gasification (SCWG) has the capacity to generate fuel gas effluent from wet biomass without previously having to dry the biomass. However, substantial efforts are still required to make it a feasible and competitive technology for hydrogen production. Biomass contains cellulose, hemicellulose and lignin, so it is essential to understand their behavior in high-pressure systems in order to optimize hydrogen production. As the main component of biomass, cellulose has been extensively studied, and its decomposition has been carried out at both subcritical and supercritical conditions. Most previous works of this model compound were carried out in batch reactors, where reaction times normally take place in a few minutes. However, the present study demonstrates that gasification reactions can achieve efficiency levels of up to 100% in less than ten seconds. The effect of temperature (450–560 °C), the amount of oxidant (from no addition of oxidant to an excess over stoichiometric of 10%, n = 1.1), the initial concentration of organic matter (0.25–2 wt.%) and the addition of a catalyst on the SCWG of cellulose in a continuous tubular reactor at short residence times (from 6 to 10 s) have been studied in this work. Hydrogen yields close to 100% in the gas phase were obtained when operating under optimal conditions. Moreover, a validation of the experimental data has been conducted based on the theoretical data obtained from its kinetics.
28 December 2015 in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
Supercritical water oxidation (SCWO) is an advanced process mainly employed for the treatment of hazardous stable wastes, otherwise treatable by incineration. It is based on the unique properties of water above its critical point ( Tc =675 K, Pc =22.2 MPa), making it a superior reaction medium for the destruction of all organics in the presence of oxygen. This work presents preliminary laboratory scale studies on SCWO of nitrogen (N)-containing hazardous hydrocarbons, with a view to enhancing the process performance, using available reagents and non-complex reactor design. This article investigates the destruction of dimethylformamide (DMF), carried out in a continuous (plug flow) reactor system. SCWO of DMF was enhanced by (i) a split-oxidant system, where stoichiometric oxidant was divided between two inlet ports at various ratios and (ii) the addition of isopropyl alcohol (IPA) as a co-fuel, premixed with the feedstock. Testing a range of temperatures, initial DMF concentrations, oxidant ratios, IPA ratios and oxidant split ratios, selected results were presented in terms of % total organic carbon and % N removal. Reaction kinetics were studied and showed a dramatic decrease in the activation energy upon adding IPA. Split-oxidant-feeding enhancement depended on the split ratio and secondary feed position.