Muhtar Muhtar

Dr. Muhtar Muhtar

Department of Civil Engineering, University of Muhammadiyah, Jember, Jawa Timur, Indonesia
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2019 in Data in Brief
Verified
Journal Article
Open access
Muhtar MuhtarMuhtar Muhtar
Muhtar Muhtar
The bamboo treatment process starts with cutting, soaking in water, draining in free air, reinforcing in the fireplace, first-stage adhesive coating, hose-clamp installation, second-stage adhesive coating, and sand resurfacing. Data was taken from experimental testing of bamboo materials and bond strength tests of bamboo reinforcement in the laboratory of the Faculty of Engineering, University of Brawijaya Malang. The aim of treating and strengthening bamboo reinforcement is to overcome low-load capacity and prevent collapse due to slippage in bamboo reinforced concrete elements. Adhesive coating is employed to increase durability and prevent water absorption, while installing hose-clamps increases bamboo reinforcement slip resistance. The process outlined here represents the way to approach bamboo reinforcement, and laboratory data is processed into graphic images and tables of bond strength of bamboo reinforcement providing the basis for further research. This article comprises a standard operating procedure for treatment of bamboo reinforcement, graphic images, documentation photos, and data tables. The data is related to "Enhancing bamboo reinforcement using a hose-clamp to increase bond-stress and slip resistance" [1].

27 August 2020 in Crystals
Verified
Journal Article
Open access
PDF file
Muhtar MuhtarMuhtar Muhtar
Muhtar Muhtar
AGAmri Gunasti
Amri Gunasti
SUSuhardi
Suhardi
NUNursaid
Nursaid
IRIrawati
Irawati
Rofi HamduwibawaRofi Hamduwibawa
Rofi Hamduwibawa
Stiffness is the main parameter of the beam’s resistance to deformation. Based on advanced research, the stiffness of bamboo-reinforced concrete beams (BRC) tends to be lower than the stiffness of steel-reinforced concrete beams (SRC). However, the advantage of bamboo-reinforced concrete beams has enough good ductility according to the fundamental properties of bamboo, which have high tensile strength and high elastic properties. This study aims to predict and validate the stiffness of bamboo-reinforced concrete beams from the experimental results data using artificial neural networks (ANNs). The number of beam test specimens were 25 pieces with a size of 75 mm × 150 mm × 1100 mm. The testing method uses the four-point method with simple support. The results of the analysis showed the similarity between the stiffness of the beam’s experimental results with the artificial neural network (ANN) analysis results. The similarity rate of the two analyses is around 99% and the percentage of errors is not more than 1%, both for bamboo-reinforced concrete beams (BRC) and steel-reinforced concrete beams (SRC).

10 December 2020 in Forests
Verified
Journal Article
Open access
PDF file
Muhtar MuhtarMuhtar Muhtar
Muhtar Muhtar
This paper discusses the reduction of the stiffness of bamboo reinforced concrete (BRC) beams to support the use of bamboo as an environmentally friendly building material. Calculation of cross-section stiffness in numerical analysis is very important, especially in the non-linear phase. After the initial crack occurs, the stiffness of the cross-section will decrease with increasing load and crack propagation. The calculation of the stiffness in the cross-section of the concrete beam in the non-linear phase is usually approximated by giving a reduction in stiffness. ACI 318-14 provides an alternative, reducing the stiffness of the plastic post-linear beam section through the moment of inertia (I) of the beam section for elastic analysis between 0.50Ig–0.25Ig. This study aims to predict the value of the reduction in the stiffness of the BRC beam section in the non-linear phase through the load-displacement relationship of experimental results validated by the Finite Element Method (FEM) and the Artificial Neural Networks (ANN) method. The experiment used 8 BRC beams and one steel-reinforced concrete (SRC) beam of singly reinforced with a size of 75 mm × 150 mm × 1100 mm. The beams were tested using a four-point loading method. The analysis results showed that the value of the stiffness reduction in the beam cross-sectional in the non-linear phase ranged from 0.5Ig–0.05Ig for BRC beams, and 0.75Ig–0.40Ig for SRC beams.

14 October 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Muhtar MuhtarMuhtar Muhtar
Muhtar Muhtar
Bamboo is an inexpensive, environmentally friendly, and renewable building material that thrives in Indonesia. Bamboo has a high tensile strength but also has weaknesses, namely, it is easily attacked by insects and has high water absorption. Utilization of bamboo as a precast concrete bridge reinforcement must be treated first through soaking, drying, and giving a waterproof coating and sand. This research aimed to obtain a precast bamboo reinforced concrete bridge technology with good integrity, with measuring parameters of deformation and deflection according to AASHTO standards. The dimensions of the bridge were a span of 320 cm, a width of 224 cm, and a height of 115 cm. Two bridge frames were connected by four bridge beams. The bridge plate was made of a 10-cm-thick concrete plate. The bridge support of the reinforced concrete is assumed to be the hinge support and the rubber bearing is assumed to be the roller support. The bamboo reinforced concrete frame bridge test was carried out directly with a load of a minibus-type vehicle. The test results show that the precast bamboo reinforced concrete frame bridges have sufficiently good integrity; that is, they can distribute loads with deflection and deformation that do not exceed their permits. The maximum displacement occurs in the bridge frame of 0.25 mm, meeting the requirements based on the AASTHO and RSNI T-12-2004 standards, which is not more than Δmax = L/800 = 3.75 mm. The maximum deformation occurs in the bridge beam of 0.20 mm, and the bridge frame of 0.13 mm meets the requirements based on the AASTHO and RSNI T-12-2004 standards, which is not more than δmax = L/800 = 3.75 mm.

1 April 2020 in Data in Brief
Verified
Journal Article
Open access
Muhtar MuhtarMuhtar Muhtar
Muhtar Muhtar
Numerical verification is carried out in order to control the compatibility of the BRC beam crack pattern with the stress contour at the ultimate load. The numerical method used is the finite element method (FEM) using the Fortran PowerStation 4.0 program. Material data entered is the elasticity modulus (E) and Poisson's ratio (ν). Ultimate load input data is taken from BRC beam testing in the laboratory. Bamboo reinforcement and concrete are considered to have the same displacement with a different elasticity modulus (E), so they experience different stresses. The triangle element is employed to model the plane-stress with two directions of displacement at each nodal point, so that each element has six degrees of freedom. The BRC beam tensile stress data from the Fortran PowerStation 4.0 program is processed into a tensile stress data table and becomes the Surfer program input data for mapping tensile stress zone images. Crack pattern data from laboratory beam testing is processed into crack zone pattern photo data and then compared to the tensile stress zone images. From the image data of the tensile stress zones and the crack zones of the BRC beam have compatibility. The Fortran PowerStation 4.0 programming language data in this article can be used for further research with the discretization of triangular elements in other cases. This article consists of a data table, a picture of a crack pattern zone, a drawing of tensile stress zones, and photo documentation. The data is related to "Enhancing bamboo reinforcement using a hose-clamp to increase bond-stress and slip resistance" [1].

15 March 2019 in MATEC Web of Conferences
Verified
Journal Article
Open access
Muhtar MuhtarMuhtar Muhtar
Muhtar Muhtar
SDSri Murni Dewi
Sri Murni Dewi
WIWisnumurti
Wisnumurti
AMAs’ad Munawir
As’ad Munawir
Bamboo can use at the simple concrete construction because of the tensile strength of its mechanical property. Meanwhile, a slippery surface of the bamboo caused cracks in the bamboo reinforced concrete beam (BRC) not to spread and yield slip failure between a bamboo bar and concrete. Load test at the BRC beam yield humble load capacity. This study aims to improve the capacity and behavior of BRC beam bending by giving waterproof coating, sand, and hose clamp installation. The beam test specimen with the size of 75x150x1100mm made as many as 26 pieces with the variety of reinforcement. The hose clamp used on the bamboo reinforcement varies with a distance of 0 cm, 15 cm, 20 cm, and 25 cm. The testing using a simple beam with two-point loading. The test results show that BRC beams have different bending behavior compared to the steel reinforced concrete beam (SRC).