Satellite remote sensing is regularly used for wildfire detection, fire severity mapping and burnt area mapping. Applications in the surveillance of wildfire using geostationary-based sensors have been limited by low spatial resolutions. With the launch in 2015 of the AHI (Advanced Himawari Imaginer) sensor on board Himawari-8, ten-minute interval imagery is available covering an entire earth hemisphere across East Asia and Australasia. Existing active fire detection algorithms depend on middle infrared (MIR) and thermal infrared (TIR) channels to detect fire. Even though sub-pixel fire detection algorithms can detect much smaller fires, the location of the fire within the AHI 2 × 2 km (400 ha) MIR/TIR pixel is unknown. This limits the application of AHI as a wildfire surveillance and tracking sensor. A new multi-spatial resolution approach is presented in this paper that utilizes the available medium resolution channels in AHI. The proposed algorithm is able to map firelines at a 500 m resolution. This is achieved using near infrared (NIR) (1 km) and RED (500 m) data to detect burnt area and smoke within the flagged MIR (2 km) pixel. Initial results based on three case studies carried out in Western Australia shows that the algorithm was able to continuously track fires during the day at 500 m resolution. The results also demonstrate the utility for wildfire management activities.

With an increase in the frequency and severity of wildfires across the globe and resultant changes to long-established fire regimes, the mapping of fire severity is a vital part of monitoring ecosystem resilience and recovery. The emergence of unoccupied aircraft systems (UAS) and compact sensors (RGB and LiDAR) provide new opportunities to map fire severity. This paper conducts a comparison of metrics derived from UAS Light Detecting and Ranging (LiDAR) point clouds and UAS image based products to classify fire severity. A workflow which derives novel metrics describing vegetation structure and fire severity from UAS remote sensing data is developed that fully utilises the vegetation information available in both data sources. UAS imagery and LiDAR data were captured pre- and post-fire over a 300 $\mathrm{m}$ by 300 $\mathrm{m}$ study area in Tasmania, Australia. The study area featured a vegetation gradient from sedgeland vegetation (e.g., button grass $0.2$$\mathrm{m}$) to forest (e.g., Eucalyptus obliqua and Eucalyptus globulus 50$\mathrm{m}$). To classify the vegetation and fire severity, a comprehensive set of variables describing structural, textural and spectral characteristics were gathered using UAS images and UAS LiDAR datasets. A recursive feature elimination process was used to highlight the subsets of variables to be included in random forest classifiers. The classifier was then used to map vegetation and severity across the study area. The results indicate that UAS LiDAR provided similar overall accuracy to UAS image and combined (UAS LiDAR and UAS image predictor values) data streams to classify vegetation (UAS image: 80.6%; UAS LiDAR: 78.9%; and Combined: 83.1%) and severity in areas of forest (UAS image: 76.6%, UAS LiDAR: 74.5%; and Combined: 78.5%) and areas of sedgeland (UAS image: 72.4%; UAS LiDAR: 75.2%; and Combined: 76.6%). These results indicate that UAS SfM and LiDAR point clouds can be used to assess fire severity at very high spatial resolution.

A vital component of fire detection from remote sensors is the accurate estimation of the background temperature of an area in fire's absence, assisting in identification and attribution of fire activity. New geostationary sensors increase the data available to describe background temperature in the temporal domain. Broad area methods to extract the expected diurnal cycle of a pixel using this temporally rich data have shown potential for use in fire detection. This paper describes an application of a method for priming diurnal temperature fitting of imagery from the Advanced Himawari Imager. The BAT method is used to provide training data for temperature fitting of target pixels, to which thresholds are applied to detect thermal anomalies in 4 μm imagery over part of Australia. Results show the method detects positive thermal anomalies with respect to the diurnal model in up to 99% of cases where fires are also detected by Low Earth Orbiting (LEO) satellite active fire products. In absence of LEO active fire detection, but where a burned area product recorded fire-induced change, this method also detected anomalous activity in up to 75% of cases. Potential improvements in detection time of up to 6 h over LEO products are also demonstrated.

The AHI-FSA (Advanced Himawari Imager - Fire Surveillance Algorithm) is a recently developed algorithm designed to support wildfire surveillance and mapping using the geostationary Himawari-8 satellite. At present, the AHI-FSA algorithm has only been tested on a number of case study fires in Western Australia. Initial results demonstrate potential as a wildfire surveillance algorithm providing high frequency (every 10 minutes), multi-resolution fire-line detections. This paper intercompares AHI-FSA across the Northern Territory of Australia (1.4 million km²) over a ten-day period with the well-established fire products from LEO (Low Earth Orbiting) satellites: MODIS (Moderate Resolution Imaging Spectroradiometer) and VIIRS (Visible Infrared Imaging Radiometer Suite). This paper also discusses the difficulties and solutions when comparing high temporal frequency fire products with existing low temporal resolution LEO satellite products. The results indicate that the multi-resolution approach developed for AHI-FSA is successful in mapping fire activity at 500 m. When compared to the MODIS, daily AHI-FSA omission error was only 7%. High temporal frequency data also results in AHI-FSA observing fires, at times, three hours before the MODIS overpass with much-enhanced detail on fire movement.

Computational models of wildfires are necessary for operational prediction and risk assessment. These models require accurate spatial fuel data and remote sensing techniques have ability to provide high spatial resolution raster data for landscapes. We modelled a series of fires to understand and quantify the impact of the spatial resolution of fuel data on the behaviour of fire predictive model. Airborne laser scanning data was used to derive canopy height models and percentage cover grids at spatial resolutions ranging from 2 m to 50 m for Mallee heath fire spread model. The shape, unburnt area within the fire extent and extent of fire areas were compared over time. These model outputs were strongly affected by the spatial resolution of input data when the length scale of the fuel data is smaller than connectivity length scale of the fuel. At higher spatial resolutions breaks in the fuel were well resolved often resulting in a significant reduction in the predicted size of the fire. Our findings provide information for practitioners for wildfire modelling where local features may be important, such as operational predictions incorporating fire and fuel breaks, and risk modelling of peri-urban edges or assessment of potential fuel reduction mitigations.