Frequency up-converting vibration energy harvester can bridge the gap between high-frequency response and low-frequency input, greatly increasing the efficiency of energy conversion. This article proposed a novel frequency up-converting energy harvester based on 1:3 internal resonance in 2 degree-of-freedom cubic nonlinear systems. The harvester consists of two asymmetric cantilevers corresponding to two vibration degrees-of-freedom. The ratio of cantilevers’ first-order resonances is (or close to) 1:3. When excited frequency matches the resonant frequency of the first assisting cantilever, 1:3 internal resonance of the harvester system occurs, leading to drastic vibration of the second generating cantilever at its resonance. The generated voltage frequency is then three times increased. Finally, simulated and experimental results clearly proved this frequency up-converting principle. In addition, the resonant frequency tuning and wideband behaviors of the harvester were also investigated, which increased the viability of the proposed harvester under the practical environment vibrations.

Mechanical frequency up-conversion is a technique whereby a high-frequency oscillation is induced from a low-frequency source and aims to address inherent problems in low frequency vibration energy harvesting. This work presents a novel 1:2:6 internal resonances based frequency up-converting harvester in which the operation frequency is 6 times up-converted. Compared to traditional conceptual mechanisms (e.g. mechanical impact, mechanical plucking, impulsive acceleration), the proposed harvester can operate at much lower acceleration level, the missing of sound during the frequency conversion also reduces the energy consumption. Experimental measurements and theoretical simulations demonstrate that the proposed design can collect energy from ultra-low frequency (< 5 Hz) vibration sources. In addition, the harvester shows very high performance compared to the current state-of-the-art devices, a maximum 2.07 mW of average power is obtained from the fabricated prototype at the excitation frequency and level of 1.71 Hz & 0.19 g, respectively.

Topological metamaterial has been a research hotpot in both physics and engineering due to its unique ability of wave manipulation. The topological interface state, which can efficiently and robustly centralize the elastic wave energy, is promising to attain high-performance energy harvesting. Since most of environmental vibration energy is in low frequency range, the interface state is required to be designed at subwavelength range. To this end, this paper developed a topological metamaterial beam with local resonators and studied its energy-harvesting performance. First, the unit cell of this topological metamaterial beam consists of a host beam with two pairs of parasitic beams with tip mass. Then, the band structure and topological features are determined. It is revealed that by tuning the distance between these two pairs of parasitic beams, band inversion where topological features inverse can be obtained. Then, two sub-chains, their design based on two topologically distinct unit cells, are assembled together with a piezoelectric transducer placed at the conjunction, yielding the locally resonant, topological, metamaterial, beam-based piezoelectric energy harvester. After that, its transmittance property and output power were obtained by using the frequency domain analysis of COMSOL Multiphysics. It is clear that the subwavelength interface state is obtained at the band-folding bandgap. Meanwhile, in the interface state, elastic wave energy is successfully centralized at the conjunction. From the response distribution, it is found that the maximum response takes place on the parasitic beam rather than the host beam. Therefore, the piezoelectric transducer is recommended to be placed on the parasitic beam rather than host beam. Finally, the robustness of the topological interface state and its potential advantages on energy harvesting were studied by introducing a local defect. It is clear that in the interface state, the maximum response is always located at the conjunction regardless of the defect degree and location. In other words, the piezoelectric transducer placed at the conjunction can maintain a stable and high-efficiency output power in the interface state, which makes the whole system very reliable in practical implementation.

Low frequency mechanical vibrations are ubiquitous in practical environments, and how to efficiently harvest them with piezoelectric materials remains a challenge. Frequency up-conversion strategies—up-converting low frequency vibrations to high frequency self-oscillations—can improve the power density of piezoelectric materials. This paper mainly introduces a kind of frequency which up-converts piezoelectric energy harvesters based on an internal resonance mechanism, compared with the other mechanisms caused by mechanical impact, mechanical plucking, etc.; the internal resonance-based harvesters can up-convert the frequency under a condition of lower excitation level, less energy loss, and less wideband operation bandwidth. Benefits to practical vibrations also exist in these multi-degree-of-freedom nonlinear dynamic systems. Moreover, the value of the frequency up-conversion factor based on the 1:2:6 internal resonance mechanism can reach as much as six so far, which is also a quite a high frequency up-conversion value.

Solar energy harvesting devices are widely used in smart agriculture nowadays. However, when lighting conditions are weak, such as through the night or on cloudy days, efficiency decays a lot. Additionally, as time goes by, more and more dust and bird droppings accumulate on the panel, which decreases the performance significantly. This paper aims to overcome the disadvantages mentioned above, and a novel wind–solar hybrid energy harvesting approach is proposed with an oscillation-induced dust-cleaning function. A wind-induced vibration device is specially designed in order to generate electrical energy and/or clean the photovoltaic panel. While in good lighting conditions, the device could keep the panel in a stable state and optimize the photovoltaic power generation efficiency. Such a hybrid energy harvesting approach is called a “suppress vibration and fill vacancy” algorithm. The experimental platform of the proposed device is introduced, and both experimental and simulation results are attained, which prove that using this device, we could realize multiple purposes at the same time.