sitong sun

Prof. sitong sun

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 July 2023 in Sensors
Verified
Journal Article
Open access
PDF file
SSsitong sun
sitong sun
SZSheng Zhang
Sheng Zhang
Wilson WangWilson Wang
Wilson Wang
In this work, a new monitoring system is developed for bearing fault detection in high-speed trains. Firstly, a data acquisition system is developed to collect vibration and other related signals wirelessly. Secondly, a new multiple correlation analysis (MCA) technique is proposed for bearing fault detection. The MCA technique consists of the three processing steps: (1) the collected vibration signal is decomposed by variational modal decomposition (VMD) to formulate the representative intrinsic mode functions (IMFs); (2) the MCA is used to process and identify the characteristic features for signal analysis; (3) bearing fault is diagnosed by examining bearing characteristic frequency information on the envelope power spectrum. The effectiveness of the proposed MCA fault detection technique is verified by experimental tests corresponding to different bearing conditions.

17 October 2020 in Sensors
Verified
Journal Article
Open access
PDF file
SSsitong sun
sitong sun
WYWen Yang
Wen Yang
Wilson WangWilson Wang
Wilson Wang
Seatbelt state monitoring is important in intercity buses for passenger safety. This paper discusses the issues and challenges in power-saving design of radio frequency identification (RFID) sensor networks in bus seatbelt monitoring. A new design approach is proposed in this work for low-power layout and parameter setting in RFID sensor nodes in hardware and software design. A one-to-many pairing registration method is suggested between the concentrator and the seat nodes. Unlike using extra computer software to write seat identification (ID) into an integrated circuit (IC) card, the node ID in this project can be stored into the concentrator directly, which can reduce intermediate operations and reduce development costs. The effectiveness of the proposed low-power design approach is verified by some experimental tests.

6 December 2021 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
SSsitong sun
sitong sun
Jinglun XuJinglun Xu
Jinglun Xu
Wilson WangWilson Wang
Wilson Wang
In a shock wave positioning system for light weapons, the key to accurate positioning estimation of the impact point lies in the extraction of the characteristic attributes of the shock wave signal reaching each sensor in the sensor array, the proper design and modeling of the sensor array. In this work, according to the analysis of aerodynamics and the characteristics of shock wave transmission in the designed sensor array, a positioning model is developed to estimate the impact point location based on the time difference of arrival analysis. A novel correction algorithm is suggested to address the influence of wind speed so as to improve the positioning accuracy. A smart data acquisition system is developed to measure and capture the time differences of the shot wave reaching different sensors. The effectiveness of the designed sensor array, modeling technique and wind correction algorithm is verified by tests using a specifically developed experimental setup.

24 January 2022 in Sensors
Verified
Journal Article
Open access
PDF file
SSsitong sun
sitong sun
Jinglun XuJinglun Xu
Jinglun Xu
Wilson WangWilson Wang
Wilson Wang
CWChengyuan Wang
Chengyuan Wang
Smart sensors have been used in many engineering monitoring and control applications. This work focuses on the development of a new type of clinical Bluetooth thermometer, based on an improved low-power resistive transducer circuit. Most existing resistive transducers use relatively complicated circuits with higher cost and power consumption. To tackle these problems, especially in real applications, an improved low-power resistive transducer circuit is proposed in this work and is used to develop smart Bluetooth thermometers. The parameters of the resistive transducer circuit are selected by quantitative analysis and optimization to improve the performance of the low-power resistive transducer circuit. The effectiveness of the proposed design technology was verified by tests. The temperature measurement error of the new smart Bluetooth thermometer is less than 0.1 °C, which can not only meet the clinical use requirements but also has lower cost and power consumption.