This work describes the thermal stability and magnetic properties of polyvinylidene fluoride (PVDF)/magnetite nanocomposites fabricated using the solution mixing technique. The image of transmission electron microscopy for PVDF/magnetite nanocomposites reveals that the 13 nm magnetite nanoparticles are well distributed in PVDF matrix. The electroactive β-phase and piezoelectric responses of PVDF/magnetite nanocomposites are increased as the loading of magnetite nanoparticles increases. The piezoelectric responses of PVDF/magnetite films are extensively increased about five times in magnitude with applied strength of electrical field at 35 MV/m. The magnetic properties of PVDF/magnetite nanocomposites exhibit supermagnetism with saturation magnetization in the range of 1.6 × 10−3–3.1 × 10−3 emu/g, which increases as the amount of magnetite nanoparticles increases. The incorporation of 2 wt % magnetite nanoparticles into the PVDF matrix improves the thermal stability about 25 °C as compared to that of PVDF. The effect of magnetite particles on the isothermal degradation behavior of PVDF is also investigated.
In this study, the vanadium pentoxide (V2O5), functionalized carbon nanotubes (f-CNT), and polypyrrole (PPy) based composites films have been prepared through a facile synthesis method and their electrochemical performance were evaluated as freestanding negative electrodes of supercapacitor. A hydrous V2O5 gel prepared by treating V2O5 powder with H2O2 was mixed with f-CNT to obtain V2O5/f-CNT composite film. V2O5/f-CNT composite was then coated with PPy through vapor phase polymerization method. The PPy deposited on the V2O5/f-CNT prevented the dissolution of V2O5 and thus resulted in an improved the capacitance and cycle life stability for V2O5/f-CNT/PPy composite electrode. V2O5/f-CNT/PPy freestanding negative electrode exhibited a high areal capacitance value (1266 mF cm−2 at a current density of 1 mA cm−2) and good cycling stability (83.0% capacitance retention after 10,000 charge-discharge cycles). The superior performance of the V2O5/f-CNT/PPy composite electrode can be attributed to the synergy between f-CNT with high conductivity and V2O5 and PPy with high-energy densities. Thus, V2O5/f-CNT/PPy composite based electrode can effectively mitigate the drawbacks of the low specific capacitance of CNTs and the poor cycling life of V2O5.
Stereocomplex-type poly(lactic acid) (SC-PLA)/oleylamine-modified layered zinc phenylphosphonate (SC-PLA/m-PPZn) nanocomposites are successfully fabricated using a solution mixing process. Wide-angle X-ray diffraction (WAXD) analysis reveals that the structural arrangement of the oleylamine-modified PPZn exhibits a large interlayer spacing of 30.3 Å. In addition, we investigate the temperature effect on the real-time structural arrangement of PPZn and m-PPZn. The results indicated that the lattice expansion of m-PPZn with increasing temperature leads to an increase in the interlayer spacing from 30.3 to 37.1 Å as the temperature increases from 30 to 150 °C. The interlayer spacing decreases slightly as the temperature further increases to 210 °C. This behavior might be attributed to interlayer oleylamine elimination, which results in hydrogen bonding destruction between the hydroxide sheets and water molecules. As the temperature reaches 240 °C, the in situ WAXD patterns show the coexistence of m-PPZn and PPZn. However, the layered structures of m-PPZn at 300 °C are almost the same as those of PPZn, after the complete degradation temperature of oleylamine. The morphology of the SC-PLA/m-PPZn nanocomposites characterized using WAXD and transmission electron microscopy (TEM) demonstrates that most partial delamination layered materials are randomly dispersed in the SC-PLA matrix. Small-angle X-ray scattering reveals that higher crystal layer thickness and lower surface free energy is achieved in 0.25 wt% SC-PLA/m-PPZn nanocomposites. These results indicate that the introduction of 0.25 wt% m-PPZn into SC-PLA reduces the surface free energy, thereby increasing the polymer chain mobility.
This study focuses on modifying the surface of an AA 5052-H32 aluminum alloy using plasma treatment. Discharge power, exposure time, and working gas were adjusted as process parameters to improve the adhesion between the aluminum alloy and glass fiber-reinforced thermoplastic (GFRTP) polycarbonate composite. The surface composition and morphology of the aluminum alloy sheet were analyzed by X-ray photoelectron spectroscopy and scanning electron microscopy, and surface roughness and wettability were evaluated using a surface roughness-measuring instrument and contact angle goniometry, respectively. The bonding performance of GFRTP/aluminum alloy was also assessed. The surface of the aluminum alloy was subjected to chemical treatment prior to plasma treatment. The results revealed that nitrogen plasma treatment led to a substantial increase (25%) in bonding strength due to the synergistic effect of rough surface mechanical bonding and chemical bonding through functional groups between the aluminum alloy and GFRTP. However, the improvement in surface wettability by plasma treatment is time dependent and may gradually diminish over time due to the re-adsorption of hydrocarbon contamination from the surrounding air.
Multi-element (CrHfNbTaTiVZr)N coatings were prepared through the magnetron sputtering of an equimolar CrHfNbTaTiVZr alloy target. This study determined the influences of N2-to-total (N2 + Ar) ratios (RN) on the composition, structure, mechanical properties, and electrical performance of the coatings. Coating thickness decreased from 898 nm to 128 nm with increasing RN from 0% to 100%. The alloy coating has bundles of fibrous structures with remarkable void boundaries. The coating changed from amorphous phase to face-centered cubic (FCC) phase with (111) preferred orientation, then to FCC phase with (200) preferred orientation, and finally to near-amorphous phase as RN increased from 0% to 100%. The microstructure of the nitride coatings transformed from a columnar structure with rough faceted tops and void boundaries into a dense and small structure with smooth domed tops. The grain size of the nitride coatings also decreased with RN. Accordingly, the electrical performance at high RN was poor. The nitride coating deposited at RN = 60% had the highest hardness of 16.6 GPa and the lowest friction coefficient of 0.52, owing to structural densification and grain refinement.
AlCrN and AlCrSiN coatings were deposited via reactive magnetron sputtering. This study investigates the effects of radio frequency (RF) substrate bias, ranging from 0 V to 200 V, on the chemical composition, microstructure, and mechanical properties of the coatings. All crystalline coatings exhibited a single wurtzite-type hexagonal close-packed (hcp) structure. At a 0 V substrate bias, the AlCrN coating consisted of porous V-shaped columnar crystallites, while the AlCrSiN coating exhibited a porous, fiber-like amorphous structure. As the substrate bias increased, crystal growth was promoted, void density decreased, and the surface morphology transitioned from a textured to a more rounded appearance. Additionally, the preferred orientation shifted toward the (101) direction. However, at excessively high substrate bias, re-nucleation occurred, leading to grain refinement and increased film densification, which in turn caused a further shift in the preferred orientation toward the (002) plane. Due to its multi-element composition and the low solubility of Si in nitrides, AlCrSiN coatings tend to exhibit an amorphous growth tendency during sputtering. As a result, their microstructure is more sensitive to substrate bias. This sensitivity results in the formation of a highly dense structure with an optimal crystallite size at a substrate bias of 100 V, leading to a hardness of 22.6 GPa—surpassing that of the AlCrN coating.