The nickel-iron-based alloy Inconel 718 is a progressive material with very good mechanical properties at elevated and lower temperatures. It is used both as wrought and cast alloys as well as material for additive manufacturing technologies. This is the reason why it has received so much attention, as supported by numerous publications. However, these are almost exclusively focused on a specific type of production and processing, and thus only report differences in the mechanical properties between samples prepared by different technologies. Therefore, the major aim of this research was to show how the structure and mechanical properties differ between samples produced by conventional production (wrought alloy) and additively manufactured SLM (Selective Laser Melting). It is shown that by applying appropriate heat treatment, similar strength properties at room and elevated temperatures can be achieved for SLM samples as for wrought samples. In addition, the mechanical properties are also tested up to a temperature of 900 °C, in contrast to the results published so far. Furthermore, it is proven that the microstructures of the wrought (here rolled) and SLM alloys differ significantly both in terms of grain shape and the size and distribution of precipitates.

The article presents the results of research on the influence of temperature and time changes of the annealing process on the values and distribution of stresses in the simulated heat-affected zone of S700MC steel welded joints. For this purpose, tests were carried out on a thermal cycle simulator, as well as heating the prepared samples in accordance with the recorded welding thermal cycles, and then annealing at temperatures from 200 to 550 °C. The stresses values in the tested samples before and after the annealing process were measured by using X-ray diffraction (XRD). The performed tests were verified with the results of numerical analyses using the finite element method (FEM) performed in the VisualWeld (SYSWELD) environment as, on the one hand, the verification of the obtained results, and, on the other hand, the source of data for the development of a methodology for conducting analyses of heat treatment processes of S700MC steel welded structures. Also presented are three examples of numerical analyses for Gas Metal Arc (GMAW), laser and hybrid welding and then the annealing process of the obtained joints at selected temperatures. The main purpose of the work was to broaden the knowledge on the influence of annealing parameters on the values and distribution of stresses in welded joints, but also to signal the possibility of using modern software in engineering practice.

High-strength steels are used more than general structural steel due to their combination of properties such as high strength, good toughness and weldability. They are mainly used in the manufacture of heavy vehicles for the mining industry, cranes, transportation, etc. However, welding these grades of steel brings new challenges. Also, a simulation for welding high-strength steel is required more often. To insert a material database into the simulation program, it is necessary to conduct investigations using CCT (Continuous Cooling Transformation) diagrams, welded joints research, and more. To investigate the behavior of S960MC steel during heating and cooling, we used dilatometry analysis supported by EBSD (Electron Backscatter Diffraction) analysis. A CCT diagram was constructed. The transformation temperatures of A_c1 and A_c3 increase with increasing heating rate. The A_c1 temperature increased by 54 °C and the A_c3 temperatures by 24 °C as the heating rate increased from 0.1 °C/s to 250 °C/s. The austenite decomposition temperatures have a decreasing trend in the cooling phase with increasing cooling rate. As the cooling rate changes from 0.03 °C/s to 100 °C/s, the initial transformation temperature drops from 813 °C to 465 °C. An increase in the cooling rate means a higher proportion of bainite and martensite. At the same time, the hardness increases from 119 HV10 to 362 HV10.

Secondary and backscaterred electrons are the most common signals used for imaging in the scanning electron microscopy. Generally, SE are used to obtain topographical contrast while BSE show differences in chemical composition (so called Z-con...

Diffusion bonding has many advantages, but it also has its specifics. When creating heterogeneous joints, problems arise with the creation of intermetallic phases. For this reason, an interlayer is needed to prevent the creation of these unfavorable phases. It is important to ensure that the interlayer is of sufficient thickness to prevent the elements from diffusing through the entire interlayer and the intermetallic phases from being formed again. Conversely, too thick an interlayer causes an increase in the heterogeneity of the bond properties. The creation of the initial diffusion bonds in a heterogeneous diffusion joint of AISI 304 and AISI 316L steel with a 0.2 mm thick nickel interlayer was made in a Gleeble 3500. The experiments to determine the diffusion kinetics were carried out in a vacuum furnace, with subsequent evaluation by EDX (Energy Dispersive X-ray Spectroscopy) analysis. Subsequently, the diffusion coefficients of nickel into both steels were determined, and generalized equations were formulated to calculate the diffusion coefficients for temperatures in the range of 950 to 1150 °C and holding times in the range of 3600 to 18,000 s. Equations are also given to determine the width of the diffused zone between each steel and the Ni interlayer.