To study texture of pavement surfaces and its effect on pavement friction, this article features a field experiment conducted on in-service pavements to characterize surface texture by spectral analysis to substantiate links to friction values. Pavement friction was measured using a Mu-meter and British pendulum tester whereas texture data was collected using a stationary laser profilometer. Texture spectra were analyzed and expressed in third octave bands. The correlation between texture spectral levels and friction values at different speeds are discussed in the paper. Results show that the texture level, including spectral band levels, can well represent texture characteristics, as texture spectral levels have a good correlation with friction coefficient, especially the texture level of texture wavelengths at 1.25–12.5 mm versus SFC_sl (representing the slope of the side force coefficient (SFC) versus speed), i.e., the slope of friction versus speed. This friction parameter gives better correlations with texture parameters than friction values at different speeds, which is believed to be an effect of the drainage caused by texture in that wavelength range.

Based on attenuated total reflection Fourier-transform infrared (ATR-FTIR) spectroscopy and principal component analysis (PCA), four kinds of asphalt (two kinds of matrix asphalts, TPC70# and JL70# and two kinds of modified asphalts, SBS-1 and SBS-2) were aged using the rolling thin-film oven test (RTFOT). The multiple stress repeated creep recovery test (MSCR) was carried out on an AR1500ex dynamic shear rheometer (DSR). The PCA was carried out on the attenuated total reflection infrared spectrum of a pretreated aged asphalt, the principal component factors (oxidation factor and component change factor) were determined, the comprehensive index F was calculated, and a prediction model of aging time history was established and verified. A prediction model for the aging asphalt recovery rate R was established based on the functional group index. The relationship between the recovery rate R and aging time history of each aging asphalt was analyzed and the fatigue life of each aging asphalt based on the rate of dissipated energy change (RDEC) was compared. The correlation between the comprehensive index F and fatigue life of asphalt was also analyzed. The results show that the order of resistance to the high-temperature deformation of each aging asphalt is as follows: SBS-2 > SBS-1 > TPC70# > JL70#; the prediction model of aging asphalt recovery rate R based on functional group index has good reliability. Taking the loading cycle corresponding to the sudden increase of the inflection point of the curve, i.e., the fatigue life N_RDEC, as the evaluation index, the fatigue life order of each aging asphalt is SBS-1 > SBS-2 > JL70# > TPC70#. There is a positive correlation between the fatigue life of aged asphalt and the comprehensive index F of asphalt. The correlation degree R² is 0.85; i.e., with the increase of the comprehensive index F of asphalt, its fatigue life also increases. It was found that it is feasible to analyze the aging time history and fatigue life of asphalt by infrared spectroscopy, and it can provide a rapid and non-destructive prediction method for the practical engineering application of asphalt.

In this work, to analyse the changing characteristics of contact stresses in the tyre–pavement interface and the functional relationship between rolling resistance and the working conditions of truck-bus tyres, a three-dimensional tyre–pavement model is established and used to predict the distribution of contact stresses and rolling resistance under different working conditions of the tyre, comprising various tyre loads, inflation pressures, and velocities. Results show that the magnitude relationship between transverse and longitudinal contact stresses is related to rolling conditions, and overload and low tyre pressure are important contributors to the wear of the tyre shoulder. In addition, the proposed exponential equation presents a method that can be used to forecast rolling resistance related to the working conditions of the truck-bus tyre, and a similar method can be used to predict the rolling resistances of other types of tyres.

The mechanical properties of polyurethane grouting materials were significantly improved when cement, sodium meta-silicate, red mud, slag, and fly ash were added. However, the grouting mechanisms of polyurethane composite materials are not clear. The grouting mechanisms of polyurethane composite materials in asphalt pavement subsidence were investigated. The results of computed tomography analysis show that polyurethane foam is filled with geopolymer hydration products. The results from ground penetrating radar after grouting show that mapping has no significant fluctuation or dislocation effect, which indicates that the grouting effect is strong. The high-density electrometer can also test the pavement subsidence place and distribution. The grouting mechanisms indicate that polyurethane foam acts as the consolidation structure, and the geopolymer filled with the foam pores of polyurethane and geopolymer forms a stable consolidated body. The seriflux includes under-layer seriflux (red mud, slag, water, and polyurethane composite materials) and upper-layer seriflux (polyurethane seriflux), and there exists a weak phase separation phenomenon, in which the separation phase is mainly polyurethane with little red mud-based geopolymer.

High-content waste-rubber-modified asphalt (HRMA) has high viscosity and poor storage stability. HRMA not only improves the properties of road asphalt, but also reduces the environmental pollution caused by waste tires. Enhancing the molecular interaction of waste rubber and asphalt is key to making full use of HRMA. In this paper, aromatic oil was used as the activator for waste rubber. The molecular interaction mechanism between aromatic oil and HRMA was investigated. The radial distribution function, diffusion coefficient, free volume, solubility parameter, and shear viscosity were calculated through molecular simulations. Storage stability, micromorphology, and adhesive force were measured via experiments. The adhesive force of HRMA−1 (4.9 nN) was lower than that of RMA (6.2 nN) and HRMA−2 (5.8 nN). The results show that aromatic oil can promote the dispersion of waste rubber, making the storage of asphalt systems stable. There exists a strong electrostatic force between rubber and asphaltenes and an intermolecular force between rubber and aromatic oil or aromatics, which makes the aromatic oil and aromatics of parcel rubber molecules and waste rubber highly soluble in asphalt. Molecular simulations confirmed the molecular interaction between rubber and aromatic oil, and aromatic oil was shown to reduce the viscosity of HRMA.

A tire’s three-dimensional stress for pavement is an important cause of asphalt pavement disease. In order to study the contact stress distribution between the tire and the pavement under real conditions, a sensor that can measure the tri-axial stress synchronously is designed, and a complete measurement system is established. The variation trend and stress value of tri-axial stress under steady rolling of the tire were obtained, and the stress distribution characteristics were analyzed. The results show that the stress in the three directions near the tire shoulder is greater than that in the crown area, and the stress peak moves gradually from front to back with the rolling of the tire. Compared with the simplified simulation model, these results provides valuable suggestions for exploring the real tire-pavement interaction.