This paper presents an examination of the fatigue characteristics of cement-treated base (CTB), a cement-stabilized material for use in road pavement construction based on CTB beam test specimens prepared and tested under laboratory conditions. The beam fatigue protocol for asphalt concrete, following the Austroads standard test method of AG:PT/T233, were adapted to examine the fatigue characteristics of the CTB test specimens. Standard road base (Granite/Diorite) from the local quarry in Western Australia was employed as the parent material of CTB. The beam-fatigue tests were conducted under the strain-controlled (constant strain) and stress-controlled (constant stress) testing conditions with varying cement contents (3–10%) of CTB test specimens. Two different loading waveforms of sinusoidal and haversine load curves were also investigated. The results show that for the strain-controlled testing condition, the fatigue characteristics of the CTB test specimens were not affected by the difference ...
The dynamic moduli have been recently introduced and effectively used to express the intrinsic behaviour of the viscoelasticity of an asphalt concrete material across a given range of temperatures and frequencies. Those can generally be represented in a form of the master curve. This study investigated the dynamic moduli of Western Australian (WA) asphalt mixes. In addition, the study modified the dynamic modulus predictive equation of the national cooperative highway research program (NCHRP) project 1-37A to suit WA conditions. Furthermore, in this study, the effect of increased temperatures due to climate change upon flexible road pavement was investigated through the pavement design exercise using WA as the study area. To determine the effective dynamic modulus (|E*|eff), temperature and historical climate data were sourced from a Perth Airport Station to conduct a pavement design exercise. This data covered a 20-year period, a typical asphalt pavement design life. The allowable number of cycles (of traffic) to failure (Nf) under four different pavement design scenarios was then calculated based on this |E*|eff to examine of an increase in temperature potentially resulting from climate change effects. The results of the examination showed that once an increase in temperature due to climate change was taken into account, Nf could be decreased by approximately six million repetitions. This equals a shorter pavement life or design period of around four years compared to a result of the original design, which does not consider the increase in temperature resulting from climate change.
Sustainable urban development is an increasingly important concept as cities around the world continue to grow and face challenges related to urbanization, including environmental degradation, social inequality, and economic instability. Chiang Mai is a rapidly growing city in Thailand that steers towards sustainability. In this work, we examine the state of sustainable urban development in Chiang Mai by analyzing various indicators, including transportation, waste management, air quality, and energy consumption. A multi-dimensional framework was used to assess the sustainability of Chiang Mai. Our analysis suggests that while Chiang Mai has made progress in some areas of sustainable urban development, such as promoting green transportation and waste reduction and reduction consumption, there are still many challenges to be addressed, particularly in air pollution, water management, transportation and energy consumption. We conclude by discussing the implications of our findings for policy makers, urban planners, and other stakeholders interested in promoting sustainable urban development. This study assesses Chiang Mai’s sustainability using a comprehensive set of 35 indicators. It was found that Chiang Mai has potential for sustainable development, but some indicators require improvement. The study presents guidelines for prioritizing sustainable development, improving air and water quality, promoting sustainable tourism, enhancing waste management, transportation management and energy consumption. This research provides alternative framework for evaluating cities and presents a valuable contribution to the field of sustainable urban development.
Traffic accidents are a major cause of death in Thailand. Thailand is ranked third in the world by the World Health Organization for traffic-related deaths. Decreasing road accidents is one of the Thailand National Strategy Goals and also the United Nations Sustainable Development Goals. Several traffic calming tools for school areas were reviewed for safety improvement. An approach of creating a three-dimensional piano-keyboard-styled pedestrian crossing was implemented. It used a one-point perspective technique to increase driver perception when approaching a pedestrian crossing. The assessment data were observed during 12 weeks of a school semester. A roadside camera was used to record vehicles during the morning peak, midday off-peak, and evening peak traffic. The vehicles’ average speeds were used to compare the pre- and post-installation safety. The results showed that after the new crossing was installed, vehicle speeds drastically decreased. After three weeks, vehicle speeds began to increase. After twelve weeks, the vehicle speeds had gradually increased toward the same level as before the installation. A z-test was performed at the 95% significance level (p-value 0.05), showing that the new crossing approach had only affected vehicle speed during the first three weeks post-installation. Driver familiarity behavior and faded paint were major factors in the results.
Background: Depression is a common mental health problem that can affect everyone at different stages of development. Though the prevalence rate of depression among university students is rising, exploration among engineering students is limited. The aim of the study was to examine the prevalence of depression and its associated factors of among engineering students in Thailand. Methods: A total of 346 students participated in this study. All completed the outcome inventory depression subscale (OI-D) to evaluate the level and prevalence of depression. Other variables assessed included social skills, learning styles, relationship satisfaction, interpersonal difficulty, alcohol use, internet addiction, and neuroticism. Correlation and regression analyses were applied to test the association between sociodemographic and psychosocial factors and depression. Results: Of the 346 students with the mean age of 20.25 (SD, 1.33), 52.31% were male. Based on the OI-D, 35.3% of participants exhibited symptoms indicative of major depression. Multiple regression showed that only neuroticism, interpersonal difficulties, social skills, and self-esteem appeared to be the significant predictors of depression. Conclusion: The prevalence of depression among engineering students in Thailand was unexpectedly high compared with the prevalence of depression among engineering students in some other countries. Intra- and interpersonal factors were found to be associated with depression. Further study on identifying these risk factors should be encouraged.
One of the main failure modes of a cement-stabilized road pavement base is the shrinkage cracking which could lead to negative consequences up to the failure of road pavements. The compaction time delay and cement content inherently affect to the shrinkage characteristics of the cement stabilized base course. This research aims to investigate the shrinkage characteristics with respect to the compaction time delay of a cement-stabilized base material through laboratory experiments. A series of shrinkage tests were performed on cement stabilized base samples with varying 3%, 4% and 5% of cement contents under controlled compaction delay periods varied from 0.5 hours to 1 day. The results of this study showed that shrinkage values of the study cement stabilized base increase with longer compaction time delay periods and cement contents. In addition, during an early stage (1-14 days) of shrinkage tests, shrinkage sharply increases before reaching the stage of a relatively constant rate after 14 days of testing. It would also be further notice that around 80% of the maximum shrinkage values from all tests gains in a test period between 14-21 days out of 42 days of a total shrinkage measurement period. Finally, the mathematic shrinkage model was formulated based on the test results of the study. In the model, the main factors of compaction delay time, cement content, and curing periods were used as the model variables. Shrinkage values can be predicted with a reliability of the R2 value of 0.6755.
About Me
Civil Engineering Department, Faculty of Engineering, Chiang Mai University, Chiang Mai, THAILAND
Civil Engineering Department, Faculty of Engineering, Chiang Mai University, Chiang Mai, THAILAND