In this paper, Maple software is used to study a solar cell modelled by an electronic circuit containing five physical parameters. The physical parameters are: the series resistance, the shunt resistance, the diode reverse saturation current, the diode ideality factor and the photocurrent (see figure 1). First, the characteristic equation is solved in order to find the output current as a function of the output voltage of the solar cell. Second, the expressions of the short circuit current, the open circuit voltage, the dynamical resistance of the solar cell and different kinds of powers involved: the output power, the power dissipated by Joule effect in the internal components of the solar cell and the solar cell total power are determined analytically. Finally, the effects of the different physical parameters on the characteristic and on the delivered power of the solar cell are studied and analyzed.
In the current work, the exact analytical expression of the current–voltage characteristics, which are given in terms of the function, is used to extract the physical parameters of organic and inorganic Schottky barrier diodes (SBDs). The extraction is achieved by a variety of methods using the experimental I–V characteristics. The organic SBD is based on a Poly (3-hexylthiophene-2,5-diyle) conjugated polymer (P3HT) with Al contact, measured at 300 K. Regarding the inorganic SBDs, one is based on Iridium–Silicon Carbide (Ir–SiC), measured at 300 K, and the second diode is based on Gold–Gallium Arsenide (Au–GaAs), measured at 200 K. The numerical characteristics based on the physical parameters extracted by the presented methods are in good agreement with the experimental data. The determination coefficient of the modeling methods for the three SBDs is higher than 99.99%.
Tandem solar cells have the potential to be more efficient than the Shockley–Queisser limit imposed on single junction cells. In this study, optical and electrical modeling based on experimental data were used to investigate the possibility of boosting the performance of kesterite/c-Si tandem solar cells by inserting an alternative nontoxic TiO2 buffer layer into the kesterite top subcell. First, with SCAPS-1D simulation, we determined the data reported for the best kesterite (CZTS (Eg = 1.5 eV)) device in the experiments to be used as a simulation baseline. After obtaining metric parameters close to those reported, the influence on the optoelectronic characteristics of replacing CdS with a TiO2 buffer layer was studied and analyzed. Different top subcell absorbers (CZTS0.8Se0.2 (Eg = 1.4 eV), CZTS (Eg = 1.5 eV), CZTS (Eg = 1.6 eV), and CZT0.6Ge0.4S (Eg = 1.7 eV)) with different thicknesses were investigated under AM1.5 illumination. Then, to achieve current matching conditions, the c-Si bottom subcell, with an efficiency at the level of commercially available subcells (19%), was simulated using various top subcells transmitting light calculated using the transfer matrix method (TMM) for optical modeling. Adding TiO2 significantly enhanced the electrical and optical performance of the kesterite top subcell due to the decrease in parasitic light absorption and heterojunction interface recombination. The best tandem device with a TiO2 buffer layer for the top subcell with an optimum bandgap equal to 1.7 eV (CZT0.6Ge0.4S4) and a thickness of 0.8 µm achieved an efficiency of approximately 20%. These findings revealed that using a TiO2 buffer layer is a promising way to improve the performance of kesterite/Si tandem solar cells in the future. However, important optical and electrical breakthroughs are needed to make kesterite materials viable for tandem applications.
24 February 2025 in Materials Chemistry and Physics
The inverted organic solar cell devices (iOSCs) were fabricated with different weight ratios 1:0.6, 1:0.8, and 1:1 of P3HT and PCBM, respectively. The photo-physical properties of these devices with varying weight ratios are investigated. We find that the absorption spectra revealed a decrease in the intensities with increasing the fullerene ratio and the peaks were blue shifted. Thin films morphology is evaluated by atomic force microscopy (AFM). The PL quenching suggests that the transfer of photo-induced electrons from P3HT to PCBM increases hugely with an increase in the amount of PCBM. Raman spectroscopy for devices shows a strong reduction in the crystallinity by increasing the ratio of fullerene within the blend. The J-V measurements for all devices were performed under the illumination of simulated AM 1.5 sunlight at 100 mW/cm2. External quantum efficiency (EQE) and Internal quantum efficiency (IQE) measurements are also performed for the best device. The best performance was recorded for the device with 1:1 weight ratio of P3HT and PCBM give Power Conversion Efficiency (PCE) of 3.67%, in contrast to 3.36% for (1:0.8) and 2.51% for 1:0.6 devices.
Morphological properties of two p-type semiconductors, used separately with fullerene: MEH-PPV and the commonly used P3HT, are investigated in order to study their influence on optical and Photoconductivity properties of organic thin films based on MEH-PPV/P3HT, separately, with and without PCBM. The aim is to better understand the charge carriers mechanisms inside the polymers and the effect of PCBM when added in blend. To measure morphologic and optical properties of the prepared thin films, different characterizations are performed. A comparative study of both polymers is discussed using X ray diffraction, absorption, photolumenescence and Raman spectra.