Marllory Isaza Ruiz

Ms. Marllory Isaza Ruiz

Centro de Investigación, Innovación y Desarrollo de Materiales–CIDEMAT, Facultad de Ingeniería, Universidad de Antioquia, Calle 70 No.52-21, 050010 Medellín, Colombia
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2019 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
HNHassan Nazir
Hassan Nazir
MBMariah Batool
Mariah Batool
FBFrancisco Javier Bolivar
Francisco Javier Bolivar
MRMarllory Isaza Ruiz
Marllory Isaza Ruiz
XXXinhai Xu
Xinhai Xu
AKArunachala M. Kannan
Arunachala M. Kannan

1 April 2021 in Solar Energy Materials and Solar Cells
Verified
Journal Article
Closed access
MRMarllory Isaza Ruiz
Marllory Isaza Ruiz
RMRosa Mondragón
Rosa Mondragón
FOFrancisco Bolívar Osorio
Francisco Bolívar Osorio
JVJorge Ventura-Espinosa
Jorge Ventura-Espinosa
LHLeonor Hernandez
Leonor Hernandez

1 October 2016 in Ceramics International
Verified
Journal Article
Closed access
MRMarllory Isaza Ruiz
Marllory Isaza Ruiz
JHJoseph Henon
Joseph Henon
ODOlivier Durand-Panteix
Olivier Durand-Panteix
GEGregory Etchegoyen
Gregory Etchegoyen
FRFabrice Rossignol
Fabrice Rossignol
PMPascal Marchet
Pascal Marchet

1 November 2022 in Ingeniería e Investigación
Verified
Journal Article
Open access
PDF file
MRMarllory Isaza Ruiz
Marllory Isaza Ruiz
FBFrancisco Javier Bolivar
Francisco Javier Bolivar
This study presents a new two-step method to synthesize molten salt-based nanofluids by replacing water with butanol and using an Emax high-energy mill to ensure good stability and homogeneity. Commercial HITEC molten salt was selected as the base fluid, and alumina nanoparticles (nominal size of 5,1 nm) were used as an additive in three different proportions: 0,5, 1,0, and 1,5 wt.%. The specific heat capacity was evaluated through two different methods: differential scanning calorimetry (DSC) and modulated differential scanning calorimetry (MDSC). According to the evaluation by MDSC, an increment of up to 4,27% in the specific heat capacity was achieved with 1,0 wt.% of alumina nanoparticles in comparison with the raw salt, without affecting the melting point and thermal stability of the salt. This behavior may be related to the good distribution of the nanoparticles in the salt. However, no significant improvement in the specific heat capacity of the nanofluid was observed when the standard DSC method was applied. This behavior may be due to the different sensitivities of the two methods to small changes in the sample, with MDSC being the more sensitive technique, as it establishes the contribution of the two phases that make up the nanofluid: the molten salt as the base fluid and the solid nanoparticles. Similarly, the heating rate used in each of the techniques can influence the sensitivity with regard to determining changes in nanofluids.

30 April 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
JEJorge Estebanez
Jorge Estebanez
PGPelayo García-Acevedo
Pelayo García-Acevedo
MRMarllory Isaza Ruiz
Marllory Isaza Ruiz
JDJavier Diez-Sierra
Javier Diez-Sierra
Lilián Claudia Gómez AguirreLilián Claudia Gómez Aguirre
Lilián Claudia Gómez Aguirre
José RivasJosé Rivas
José Rivas
The conversion of electricity into heat via power-to-heat (P2H) technologies is increasingly critical for renewable energy integration, yet conventional resistive heating suffers from surface-localized energy deposition, thermal gradients, and hot spot formation. Here, we report a magnetothermal approach to volumetric heat generation based on Fe₃O₄/HELISOL® nanofluids, the first demonstration of magnetic hyperthermia in a commercial non-polar heat transfer fluid. Monodisperse magnetite nanoparticles (18.4 ± 1.9 nm), synthesized via thermal decomposition and surface-stabilized with an oleylamine/oleic acid shell, are stably formulated in HELISOL® 10A, a silicone-based fluid engineered for concentrated solar power and high-temperature industrial applications. Under alternating magnetic fields (20 mT, 985 kHz), the nanofluids deliver specific absorption rate (SAR) values up to 600 W·g-¹ and ultrafast bulk heating (ΔT ≈ 50 °C in under 10 s at 20 mg·mL-¹). Systematic evaluation over three weeks, including repeated thermal aging cycles (70 °C, 6 h) and continuous magnetic cycling, confirms operational stability with less than 10% performance loss. Heat generation is governed by Néel and Brown relaxation mechanisms, with concentration-dependent dipolar interactions modulating energy dissipation efficiency. A thermodynamic model enables predictive estimation of temperature rise as a function of nanoparticle loading, providing a practical framework for process scale-up. These results demonstrate that magnetically responsive nanofluids can function as active, contactless heat-generation media in industrially relevant fluids, opening new engineering routes for scalable P2H and thermal energy storage systems.

1 January 2025 in Revista Facultad de Ingeniería Universidad de Antioquia
Verified
Journal Article
Open access
PDF file
MRMarllory Isaza Ruiz
Marllory Isaza Ruiz
MRMagali Restrepo-Posada
Magali Restrepo-Posada
HRHarold Emanuel Rebellon
Harold Emanuel Rebellon
MBMaryory Astrid Gómez Botero
Maryory Astrid Gómez Botero
The Department of Antioquia, Colombia, produces 47% of the mining tailings linked to national gold extraction. These residues, stored in dam-like deposits, contain toxic substances such as heavy metals, posing serious risks to the environment and public health. Due to their high silica and alumina content, these tailings could be repurposed as alternative cementitious materials. Hybrid cements, formed by combining Portland cement with alkaline-activated materials, offer a lower environmental impact and support circular economy practices. In this study, the potential use of Antioquia’s mining tailings as precursors for hybrid cement production was evaluated. Sodium carbonate and sodium silicate were used as alkaline activators, and curing was performed at room temperature. The tailings’ chemical composition showed suitable levels of silica and alumina for geopolymer synthesis. Concrete specimens were prepared using hybrid cement and three types of aggregates: sand, coarse tailings, and recycled polymer. After 28 days of curing, the highest compressive strength was 568.6 kN ± 6.1 with coarse tailings, followed by 550.3 kN ± 7.9 with sand, and 325.3 kN ± 7.5 with recycled polymer. These results demonstrate the feasibility of using mining residues in sustainable construction applications.