Yi Jiang

Ms. Yi Jiang

Nanjing University of Aeronautics & Astronautics

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2019 in Optik
Verified
Journal Article
Closed access
YJYi Jiang
Yi Jiang
HWHaitao Wang
Haitao Wang
GTGuiyun Tian
Guiyun Tian
QYQiuji Yi
Qiuji Yi
JZJiyuan Zhao
Jiyuan Zhao
KZKai Zhen
Kai Zhen

1 July 2021 in Optik
Verified
Journal Article
Closed access
YJYi Jiang
Yi Jiang
HWHaitao Wang
Haitao Wang
SCShuai Chen
Shuai Chen
GTGuiyun Tian
Guiyun Tian

12 October 2020 in IEEE Access
Verified
Journal Article
Open access
YJYi Jiang
Yi Jiang
HWHaitao Wang
Haitao Wang
SCShuai Chen
Shuai Chen
QZQing Zhang
Qing Zhang
PHPan Hu
Pan Hu
HWHailong Wang
Hailong Wang
Selective laser melting (SLM) is an important method of additive manufacturing, however it has some disadvantages such as poor surface qualities of the formed parts and the appearances of small surface defects. In this paper, 360L stainless steel with artificial defects in different lengths are processed by SLM processing. A full noncontact laser ultrasonic-based B-scan detection system is built to detect the surface defects. The interaction between the scattered surface wave and the surface defect is verified through 3-dimension (3D) finite element simulation. In order to improve the signal-to-noise ratio (SNR) of laser ultrasonic signal in AM 316L part, Variational Mode Decomposition (VMD) algorithm based particle swarm optimization (PSO) is applied to denoise signals. Meanwhile, wavelet transform (WT) algorithm is used to compare SNR with VMD algorithm. Then, the time and amplitude parameters of different positions are extracted to realize B-scan imaging, and the lengths of defects are further accurately quantified through the time-amplitude-position imaging images. Otherwise, we find that the size of laser spot affects the precise quantification of defects. The smaller the spot is, the more precise the quantitative effect is. The results show that this method can quantitatively detect surface defects of AM 316L parts.

14 June 2012 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
MLMing Liu
Ming Liu
HWHaijun Wang
Haijun Wang
YJYi Jiang
Yi Jiang
YGYong Ming Guo
Yong Ming Guo
KZKe Zhao
Ke Zhao
The effects of internal spraying environment on the microstructures and mechanical properties of plasma spraying NiCrBSi+15%Mo coatings were investigated. For experimental analysis of spraying environment, a specialized internal plasma device and its test unit were developed. Firstly, microstructures of spraying coatings and powders were analyzed by scanning electron microscopy (SEM). Furthermore, the boding strength, porosity and micro-hardness of the coatings were investigated and determined separately. According to these properties of plasma spraying coating, the influence of spraying environment on the coating properties and specimen temperature could be investigated. The results show that that the coating performances decreased because of the dust, smog and high temperature of the internal spraying environment. The high-performance internal coatings can be obtained by properly designing spraying process and using the special spraying device.

1 August 2026 in Russian Journal of Nondestructive Testing
Verified
Journal Article
Closed access
PDF file
YJYi Jiang
Yi Jiang
KWKaizheng Wang
Kaizheng Wang
SCShuai Chen
Shuai Chen
Additively manufactured (AM) 316L stainless steel components may contain surface groove whose rapid quantitative evaluation is important for process monitoring and nondestructive inspection. Conventional laser-ultrasonic imaging approaches can provide rich geometric information, but they generally rely on dense scanning and complex trajectory planning, which limit their suitability for rapid near-line or in-service assessment. To address this limitation, this study proposes a fully non-contact double-sided laser-ultrasonic surface-wave method for quantitative measurement of surface groove width, in which pulsed laser excitation and optical interferometric detection are arranged on both sides of the groove. The groove width is estimated from the arrival times of the reflected Rayleigh-wave packets together with the known geometric spacing of the measurement points through a double-sided geometric-temporal mapping relationship. To cope with the rough surface, strong scattering, and low signal-to-noise ratio of AM 316L specimens, a PSO-optimized variational mode decomposition method (NEW-VMD) is introduced to enhance the reflected-wave feature and improve the robustness of arrival-time extraction. Simulation and experimental results demonstrate that the proposed method can achieve quantitative groove-width inversion over the range of 0.5–1.5 mm. For the specimens with groove widths of 1.0 and 1.5 mm, the relative errors remain within 3%, whereas a larger deviation is observed for the 0.5 mm groove because the reflected Rayleigh-wave packet is weaker and more susceptible to waveform overlap and noise. Overall, the proposed method provides a feasible proof-of-principle route for rapid quantitative evaluation of surface grooves in AM 316L components using a limited number of laser-ultrasonic measurement positions.