Residual surface deformation resulting from abandoned mined-out areas can lead to severe damage to ground structures (e.g., buildings and infrastructure in mining areas) and the local ecological environment. Long-term monitoring and analyses of surface deformation characteristics of abandoned mined-out areas are significant for preventing potential disasters. In this study, a detailed field investigation first was conducted in Ying’an and Baoshan coal mines located in Jilin Province, China, to survey mining-induced disasters in the mining areas. Based on the 40 Sentinel-1A images acquired from 14 February 2017 to 17 May 2020, small baseline subset interferometry synthetic aperture radar (SBAS-InSAR) technology was employed to obtain the time-series residual surface deformation. Validation of the SBAS-derived results is performed by comparing with the results obtained via leveling measurements. The root mean square error (RMSE) between SBAS-derived and leveling measurements results was found to be 1.144 mm, reflecting a fairly good agreement. Furthermore, the ordinary Kriging interpolation approach was adopted to obtain information on the deformation across the entire area. The spatial–temporal evolution characteristics of the derived subsidence bowls in multiple mined-out areas were revealed. The deformation characteristics for the abandoned mined-out areas in different periods were not completely consistent. Finally, the potential mechanism underlying the inconsistency in the subsidence associated with underground coal exploitation is analyzed. The findings of this study can provide insights into local construction and ecological improvement as well as guidance for the prediction of deformation in abandoned mined-out areas.
10 February 2017 in Marine Georesources & Geotechnology
Vacuum preloading is a soft ground improvement method that has been successfully used by geotechnical engineers and specialists to accelerate the rate of consolidation. However, consolidation efficiency is low when dealing with newly reclaimed high-clay content dredger fills because of sludge plugging of the prefabricated vertical drains. In this study, step vacuum preloading was proposed to reinforce a high-clay content dredger fill by applying the vacuum load gradually to consolidate the dredger fill fully and to reduce the migration of fine particles. An indoor simulation test was conducted, and monitoring data were obtained. Results showed that the settlements increased gradually, the pore water pressures and flow velocities decreased over time, and all the changes tended to be stable by the end of the test. The settlements at each stage were more than that at the previous stage, illustrating that changing the method of drainage consolidation in a timely manner, or increasing the vacuum pressure, can more fully consolidate the dredger fill at each stage, thus improving the consolidation efficiency of the dredger fill. The reinforcement effect of the high-clay content dredger fill was also analyzed. The results show that the moisture contents and porosities decreased gradually, the bearing capacity increased gradually in the consolidation process, and each property index of the dredger fill changed with the increase in degree of consolidation, and the regularity of the distribution of the indices showed that obvious siltation did not occur in the consolidation process. Overall, the consolidation efficiency was effectively improved. Thus, the step vacuum preloading method is suitable for high-clay content dredger fills. This method can improve the consolidation efficiency and the uniform reinforcement effect.
30 November 2018 in Bulletin of Engineering Geology and the Environment
The strength characteristics of unsaturated silty clay after the cooling and single freeze-thaw cycle were studied by using Global Digital Systems Ltd. (GDS) triaxial test system after controlling initial matric suction. The results demonstrate that, the initial matrix suction and freezing process can strengthen the shear strength of the soil, which makes the stress-strain curve of the soil show certain strain hardening characteristics at different temperatures. when the temperature is negative (including 0°C), the curve has a flat transition section whose strength does not change with deformation, and the flat transition section becomes shorter as the temperature and confining pressure decrease. The strength of the soil at negative temperature and the speed at which it reaches its peak value are much greater than those of the soil after positive temperature and single freeze-thaw cycle, and the contribution of confining pressure to the strength decreases with the decrease of temperature. The effect of temperature change (15°C to −15°C) on soil strength is mainly reflected in the total cohesion, and the effect of freeze-thaw on the effective internal friction angle is more significant. The strength and deformation characteristics of soil under the freezing process and freeze-thaw cycle are determined by the initial matric suction, the form of connection between soil particles, the migration of unfrozen water, and the degree of water-ice phase transformation.
For engineering construction in seasonally frozen regions, when the soil below the frost depth without freeze‐thaw effect was exposed or reclaimed after excavation, long‐term freeze‐thaw will change soil skeleton and porous characteristics, thereby leading to the deterioration of soil engineering properties. This study focused on seasonally frozen silty clay from Changchun, China, and conducted different freeze‐thaw cyclic tests on remoulded soil samples, during which both freezing temperature and the number of freeze‐thaw cycles were varied. The related data of pore structures under different test conditions were acquired through mercury injection porosimetry (MIP) tests, and the effects of the number of freeze‐thaw cycles and freezing temperature on the change of the soil’s pore structure were investigated in detail in combination with fractal theory. The variation rules of pores in the soil after freeze‐thaw cycles were investigated from a microperspective so as to essentially analyze the mechanism of the deteriorating effect of freeze‐thaw on a soil’s engineering properties.
As a solution to avoid the blockage of the drainage pipe by traditional vacuum preloading, step vacuum preloading (SVP) has been progressively studied. However, the effectiveness of this technique has yet to be systematically analyzed. In this study, an indoor model test was conducted in which vacuum pressure was applied in five stages (10, 20, 40, 60, and 80 kPa) to dredger soil with high clay content at a reclamation site in Binhai New Area, Tianjin, China. The extent of the consolidation effect of the soil was determined, and the effectiveness of the step vacuum preloading method to address drainage pipe blockage was evaluated. The results indicate that soil settlement increases at each stage of vacuum pressure treatment and the degree of vertical consolidation at each stage exceeds 90%. At the end of the treatment stage with vacuum pressure of 80 kPa, the weakly bound water was discharged. Dissipation of pore water pressure occurred in all stages. On the basis of these results, it is shown that SVP can efficiently reinforce dredger fill. Moreover, after SVP, the grain size of the soil and void ratio are still uniformly distributed. Regardless of their location from the drainage pipe, soil exhibits permeability coefficients within the same order of magnitude. The consolidation effect of soil in each stage and the increased drainage rate in the initial stage of vacuum preloading with 80 kPa indicate that the test in the current study can decrease the horizontal displacement of fine particles and can avoid drainage pipe blockage.