Flexural strength evaluation models for steel fiber reinforced ultra high strength concrete were suggested and evaluated with test results. Suggested flexural strength models were composed of compression stress blocks and tension stress blocks. Rectangular stress block, triangular stress block, and real distribution shape of stress were used on compression side. Under tension, rectangular stress block distributed to whole area of tension side and partial area of tension side was used. The last model for tension side is realistic stress distribution. All these models were verified with test result which was carried out in this study. Test was conducted by four-point loading with 2,000 kN actuator for slender beam specimen. Additional verifications were carried out with previous researches on flexural strength of steel fiber reinforced concrete or ultra high strength concrete. Total of 21 test specimens were evaluated. As a result of comparison for flexural strength of section, neutral axis depth at ultimate state, models with triangular compression stress block, and strain-softening type tension stress block can be used as exact solution for ultra high performance concrete. For the conservative and convenient design of section, modified rectangular stress block model can be used with strain softening type tension stress block.

Evaluation of the ultimate strength for the UHPFRC (ultra-high-performance fiber-reinforced concrete) flexural members was conducted. In this study, an experimental program about UHPFRC beams was conducted with the effect of fiber volume fraction, shear span to depth ratio, and compressive strength of matrix as the main variables. Among them, it was found that fiber volume fraction was the variable that had the greatest influence on the ultimate strength. The inclusion of 2% volume fraction steel fiber increases the shear and flexural strength of UHPFRC beams significantly. In particular, steel fiber inclusion changed the mode of failure of beams from diagonal shear failure into flexural failure. For the classification of failure patterns, the ultimate flexural strength and shear strength of UHPFRC members were evaluated using the current design code and UHPC guidelines. Flexural ultimate strength was affected by the size and shape of the stress block and consideration of the matrix’s tensile strength. For the accurate shear strength prediction of UHPFRC beams, the tensile strength of the high strength matrix and the effect of steel fiber should be considered.

Although mechanical properties of concrete under uniaxial compression are important to design concrete structure, current design codes or other empirical equations have clear limitation on the prediction of mechanical properties. Various types of fiber-reinforced reactive powder concrete matrix were tested for making more usable and accurate estimation equations for mechanical properties for ultra high strength concrete. Investigated matrix has compressive strength ranged from 30 MPa to 200 MPa. Ultra high strength concrete was made by means of reactive powder concrete. Preventing brittle failure of this type of matrix, steel fibers were used. The volume fraction of steel fiber ranged from 0 to 2%. From the test results, steel fibers significantly increase the ductility, strength and stiffness of ultra high strength matrix. They are quantified with previously conducted researches about material properties of concrete under uniaxial loading. Applicability of estimation equations for mechanical properties of concrete was evaluated with test results of this study. From the evaluation, regression analysis was carried out, and new estimation equations were proposed. And these proposed equations were applied into stress-strain relation which was developed by previous research. Ascending part, which was affected by proposed equations of this study directly, well fitted into experimental results.

The voided slab system has been known as an effective technique to replace a heavy reinforced concrete slab system without the decrease in flexural strength. However, according to the previous studies, the flexural capacities such as flexural strength, stiffness and ductility of the voided slabs were practically lower than that of the solid slabs depending on the void shapes and details. Therefore, in this study, an analytical and experimental study were conducted to derive the optimal void shape and details focused on the flexural capacities of voided slabs. Based on a finite element (FE) analysis, a donut-type void shaper, which was a hexahedron with rounded edges and a hole penetrating the center, was suggested as the optimal shape in voided slabs, and an experimental study was conducted to verify flexural capacities of the donut-type voided slab. The flexural strength, stiffness and deflection of the donut-type voided slab were investigated by void shape and fixing method of void shaper as variables. The ductility of voided slab was also evaluated, because ductility is as important as strength for the safe design of slab member. The test results showed that the flexural strength of the donut-type voided slabs was equivalent to 98% and 105% that of the solid RC specimen, and the donut-type voided slab specimens had enough ductility for the flexural member. The stiffness of the donut-type voided slab was decreased about 8~9% compared with the solid slab, but it was improved up to 7% compared to the non-donut-type voided slab. Based on test results, the flexural design method of the donut-type voided slab associated with the void shape and fixing device of void shaper was suggested, and it was confirmed that the donut-type voided slab is one of the efficient alternatives to replace heavy flat plate slabs.

In this paper, the structural performance of lap-spliced beams were investigated by the testing of 18-UHPFRC beams with and without a lap-spliced region and steel fiber. All test specimens were subjected to flexural load by using the four-point bending test. It was shown that test steel fiber inclusion in the ultra-high-strength matrix significantly increased the strength of the lap-spliced beams. The maximum strength of the specimen increased linearly with the increase in steel fiber volume fraction. The hybrid-type UHPFRC, with lower steel fiber volume fraction, using two types of steel fiber was effective in improving the bond strength. In order to verify the safety of lap splice length design methods by current code provisions and UHPFRC design recommendations, the average bond stress at the ultimate state was used to calculate the lap splice length, which makes reinforcement yielding, and this value, compared with design lap splice length. Most of the design equations were under the estimated bond stress of UHPFRC. However, the AFGC recommendation, which considers the tensile strength of UHPFRC, overestimates the bond stress of UHPFRC because this recommendation was developed from the direct pull-out test results.