Yukun Dong

Mr. Yukun Dong

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 February 2023 in Information and Software Technology
Verified
Journal Article
Closed access
YDYukun Dong
Yukun Dong
YTYeer Tang
Yeer Tang
XCXiaotong Cheng
Xiaotong Cheng
YYYufei Yang
Yufei Yang
SWShuqi Wang
Shuqi Wang

7 December 2021 in ACS Omega
Verified
Journal Article
Open access
YDYukun Dong
Yukun Dong
YZYu Zhang
Yu Zhang
FLFubin Liu
Fubin Liu
XCXiaotong Cheng
Xiaotong Cheng
Gas injection and water injection are common and effective methods to improve oil recovery. To ensure its production effect, it is necessary to simulate the oilfield production process. However, traditional composition simulation runs a large number of calculations and takes a long time. Through the analysis of relevant data, we found that production is affected by many factors and has a strong sequential character. Therefore, this paper proposes a deep learning model for reservoir production prediction based on stacked long short-term memory network (LSTM). It is applied to other well patterns with a short production time and a few samples in the same oilfield block by transfer learning. The model achieves an effective combination with the actual reservoir production process. At the same time, it uses the knowledge learned from the well pattern with sufficient historical data to assist in the establishment of the model of the well pattern with limited data. This can obtain accurate prediction results and save the model training time, thus getting more effective application effects than composition simulation. This paper verifies the effectiveness of the proposed method through the data and multiple different injection combinations of the Tarim oilfield.

26 June 2023 in Information and Software Technology
Verified
Journal Article
Closed access
YDYukun Dong
Yukun Dong
YTYeer Tang
Yeer Tang
XCXiaotong Cheng
Xiaotong Cheng
YYYufei Yang
Yufei Yang

1 April 2025 in Natural Gas Industry B
Verified
Journal Article
Open access
YDYukun Dong
Yukun Dong
XZXiaodong Zhang
Xiaodong Zhang
JZJiyuan Zhang
Jiyuan Zhang
KWKuankuan Wu
Kuankuan Wu
SLShuaiwei Liu
Shuaiwei Liu

14 April 2022 in Energies
Verified
Journal Article
Open access
PDF file
YDYukun Dong
Yukun Dong
YZYu Zhang
Yu Zhang
FLFubin Liu
Fubin Liu
ZZZhengjun Zhu
Zhengjun Zhu
The optimization of injection–production parameters is an important step in the design of gas injection development schemes, but there are many influencing factors and they are difficult to determine. To solve this problem, this paper optimizes injection-production parameters by combining an improved particle swarm optimization algorithm to study the relationship between injection-production parameters and the net present value. In the process of injection-production parameter optimization, the particle swarm optimization algorithm has shortcomings, such as being prone to fall into local extreme points and slow in convergence speed. Curve adaptive and simulated annealing particle swarm optimization algorithms are proposed to further improve the optimization ability of the particle swarm optimization algorithm. Taking the Tarim oil field as an example, in different stages, the production time, injection volume and flowing bottom hole pressure were used as input variables, and the optimal net present value was taken as the goal. The injection-production parameters were optimized by improving the particle swarm optimization algorithm. Compared with the particle swarm algorithm, the net present value of the improved scheme was increased by about 3.3%.

3 December 2020 in Symmetry
Verified
Journal Article
Open access
PDF file
XWXun Wang
Xun Wang
BLBaohua Liu
Baohua Liu
YDYukun Dong
Yukun Dong
SPShanchen Pang
Shanchen Pang
XTXixi Tao
Xixi Tao
Anthropometric dimensions can be acquired in 2D images by landmarks. Body shape variance causes low accuracy and bad robustness of landmarks extracted, and it is difficult to determine the position of axis division point when dimensions are calculated by the ellipse model. In this paper, landmarks are extracted from images by convolutional neural network instead of the gradient of body outline. A general multi-ellipse model is proposed, the anthropometric dimensions are obtained from the length of different elliptical segments and the position of axis division point is determined by thickness–width ratio of body parts. Finally, an evaluation is completed based on 87 subjects, in which it turns out that the average accuracy of our method for identifying landmarks is 96.6%, when the number of rotation angles is 2, the three main dimensional errors calculated by our model are smaller than existing method, and the errors of other dimensions are also within the margin of error for garment measuring.