Plasma sources suitable to generate low temperature plasmas has been fundamental for the advances in plasma medicine. In this research field, plasma sources must comply with stringent conditions for clinical applications. The main requirement to be met is the patient and operator’s safety and the ethical requirement of effectivity, which encompasses the electrical regulations, potential device toxicity and effectiveness in relation to the desired treatment. All these issues are addressed by the German pre-standard DIN SPEC 91315:2014–06 (DINSpec), which deals with the safety limits, risk assessment and biological efficacy of plasma sources aimed for medical applications. In this work, a low cost, user-friendly and flexible atmospheric pressure plasma jet (APPJ) device was characterized following the DINSpec guidelines. The device, which is still under development, proved to be safe for medical applications. It is capable of producing an APPJ with low patient leakage current and UV emission, gas temperature lower than 40 ∘C, production of harmful gases within the safety limits and low cytotoxicity. The most differentiating feature is that the device presented good antimicrobial efficacy even operating at frequency of the order of just a few hundred Hz, a value below that of most devices reported in the literature.

Plasma medicine is an emerging research field which has been driven by the development of plasma sources suitable to generate low temperature plasmas. In many cases, such devices can operate without a gas flow, producing a plasma discharge from the ambient air. However, the most common case is the use of a working gas at a given flow rate to produce a plasma jet. Helium (He) is one of the gases commonly used as the carrier gas to generate cold atmospheric pressure plasma jets (CAPPJs) due mainly to the easiness to ignite a gas discharge with it. However, in this work it was observed that most of the heating of a He CAPPJ can come just from the expansion of the He gas. This was found through measurements of gas temperature (T _gas ), using fiber optic temperature (FOT) sensors, and thermal output, using both FOT and infrared imaging with the He flow impinging on a copper (Cu) plate. Such findings were achieved through comparisons of T _gas and the temperature on the Cu (T _Cu ) plate in the conditions with and without discharge ignition, as well as comparing T _gas in the free gas/jet mode with and without discharge ignition. It was verified that the T _gas values increased as the distance from the gas outlet was enlarged, especially at low He flow rates, even without discharge ignition. Despite the temperature increase with distance, it is possible to produce plasma jets with temperatures lower than 40 °C at low He flow rates.

This paper studies the processing of poly(dimethylsiloxane) (PDMS) surfaces using dielectric barrier discharge (DBD) plasma in two different assemblies, one using the primary plasma jet obtained from a conventional DBD and the other using a DBD plasma jet transfer. The evolution of water contact angle in the function of plasma processing time and in the function of aging time as well as the changes in the surface roughness of PDMS samples for both plasma treatments have been studied. The vibrational and rotational temperatures are compared for both plasmas and for the first time the vibrational temperature (Tvib) for the transferred plasma jet has been shown to be higher as compared with the primary jet. The increment in the Tvib value seems to be the main reason for the improvements in adhesion properties and surface wettability for the transferred plasma jet. Possible explanations for the increase in the vibrational temperature are presented.

The therapeutic effects of atmospheric pressure plasma jets (APPJs) have been associated with the presence of reactive species, mainly the reactive oxygen and nitrogen ones, generated in this kind of plasmas. Due to that, many studies attempting to enhance the production of reactive species in APPJs have been performed. The employment of gas admixtures, usually mixing a noble gas with oxygen (${\mathrm{O}}_2$) or water vapor, is one of the most common methods to achieve such goal. This work presents a study of how the addition of small amounts of ${\mathrm{O}}_2$ affects the electrical parameters and the production of reactive species in a transferred APPJ produced at the tip of a long and flexible plastic tube. The study was carried out employing helium (He) as the working gas and applying a high voltage (HV) in the form of amplitude-modulated sine waveform (burst mode). With this configuration it was possible to verify that the ${\mathrm{O}}_2$ addition reduces the discharge power and effective current, as a result of late ignition and shorter discharge duration. It was also found that the addition of ${\mathrm{O}}_2$ to a certain content in the gas admixture makes the light emission from oxygen atoms increase, indicating an increment in oxygen related reactive species in the plasma jet. However, at the same time the light emitted from hydroxyl (OH) and nitric oxide (NO) exhibits the opposite behavior, i.e., decrease, indicating a reduction of such species in the APPJ. For these reasons, the addition of ${\mathrm{O}}_2$ to the working gas seems to be useful for increasing the effectiveness of the plasma treatment only when the target modification effect is directly dependent on the content of atomic oxygen.

Long-distance correlations (LDCs) of plasma potential fluctuations in the plasma edge have been investigated in the TCABR tokamak in the regime of edge biasing H-mode using an array of multi-pin Langmuir probes. This activity was carried out as part of the scientific programme of the 4th IAEA Joint Experiment (2009). The experimental data confirm the effect of amplification of LDCs in potential fluctuations during biasing recently observed in stellarators and tokamaks. For long toroidal distances between probes, the cross-spectrum is concentrated at low frequencies f < 60 kHz with peaks at f < 5 kHz, f = 13–15 kHz and f ∼ 40 kHz and low wave numbers with a maximum at k = 0. The effects of MHD activity on the LDCs in potential fluctuation are investigated.