Junsoo Kim

Mr. Junsoo Kim


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 April 2022 in Advanced Materials
Verified
Journal Article
Closed access
SLSiyoung Lee
Siyoung Lee
JKJunsoo Kim
Junsoo Kim
HRHajung Roh
Hajung Roh
WKWoongji Kim
Woongji Kim
SCSein Chung
Sein Chung
KCKilwon Cho
Kilwon Cho

28 September 2020 in Sensors
Verified
Journal Article
Open access
PDF file
KSKumjae Shin
Kumjae Shin
CKChayeong Kim
Chayeong Kim
MSMin Sung
Min Sung
JKJunsoo Kim
Junsoo Kim
WMWonkyu Moon
Wonkyu Moon
Miniaturized capacitive microphones often show sensitivity degradation in the low-frequency region due to electrical and acoustical time constants. For low-frequency sound detection, conventional systems use a microphone with a large diaphragm and a large back chamber to increase the time constant. In order to overcome this limitation, an electret gate on a field-effect transistor (ElGoFET) structure was proposed, which is the field-effect transistor (FET) mounted diaphragm faced on electret. The use of the sensing mechanism consisting of the integrated FET and electret enables the direct detection of diaphragm displacement, which leads its acoustic senor application (ElGoFET microphone) and has a strong ability to detect low-frequency sound. We studied a theoretical model and design for low-frequency operation of the ElGoFET microphone prototype. Experimental investigations pertaining to the design, fabrication, and acoustic measurement of the microphone were performed and the results were compared to our analytical predictions. The feasibility of the microphone as a low-frequency micro-electromechanical system (MEMS) microphone, without the need for a direct current bias voltage (which is of particular interest for applications requiring miniaturized components), was demonstrated by the flat-band frequency response in the low-frequency region.

27 May 2022 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
JKJunsoo Kim
Junsoo Kim
Siyoung LeeSiyoung Lee
Siyoung Lee
GBGeun Yeol Bae
Geun Yeol Bae
WMWonkyu Moon
Wonkyu Moon
Polymers are attractive materials for the fabrication of micro-electro-mechanical system (MEMS) microphones because of their low Young’s moduli, generally lower processing temperatures than silicon, and simple fabrication; such microphones are sensitive and economical. However, an earlier polymer diaphragm revealed lower sensitivity than expected. In addition, the viscoelastic properties of polymer diaphragm have been considered to degrade the sensing performance due to a high-level mechanical noise. Here, we investigated the possibility of the polymer material as a MEMS microphone in terms of stiffness and damping. Stiffness was analyzed and experimentally verified. The obtained polymer diaphragm damping coefficient was compared with the coefficient of a silicon MEMS microphone to explore whether performance was degraded by material damping. All samples were fabricated using a thin film transfer method. SU-8 was mainly used but Polymethyl methacrylate (PMMA) was also selected for comparing the material damping effect. The measured residual stress of an SU-8 diaphragm was 18 MPa; the measured flexibility was similar to the state-of-art of a silicon-based MEMS microphone, and it was proven that there is room for further improvement through process optimization. The damping effect induced by viscoelasticity was very small, compared with the effect of air damping; indeed, the intrinsic damping effect of the polymer on device performance was negligible. [2021-0213]

1 September 2018 in The Journal of the Acoustical Society of America
Verified
Journal Article
Closed access
PDF file
JKJunsoo Kim
Junsoo Kim
HLHoontaek Lee
Hoontaek Lee
CKChayeong Kim
Chayeong Kim
DSDonghwan Seo
Donghwan Seo
KSKumjae Shin
Kumjae Shin
WMWonkyu Moon
Wonkyu Moon
Most commercially available microphones use a capacitive method, and their structure and performance are saturated to some extent. However, due to the limitation of the capacitive transduction method, the roll-off at the low frequency is inevitable, and there is a limit in reducing the mechanical thermal noise caused by the squeeze film damping that occurs between the membrane and backplate structure. Proposed FET (field effect transistor) based MEMS microphone detects a change in the source-drain current according to the gate voltage change of the FET induced by vibrating the membrane with the electric field. In the case of a MEMS microphone using the proposed FET, low frequency roll-off according to the energy conversion does not occur, and the size of the backplate can be drastically reduced as compared with the conventional MEMS microphone, thereby further reducing the mechanical thermal noise, leading to the possibility of achieving the higher SNR (signal to noise ratio). In this study, design and fabrication, performance test of the proposed FET based MEMS microphone are conducted. [Work supported by CMTC, UM15304RD3.]

23 October 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
HLHoontaek Lee
Hoontaek Lee
JKJunsoo Kim
Junsoo Kim
KSKumjae Shin
Kumjae Shin
WMWonkyu Moon
Wonkyu Moon
We report recent improvements of the tip-on-gate of field-effect-transistor (ToGoFET) probe used for capacitive measurement. Probe structure, fabrication, and signal processing were modified. The inbuilt metal-oxide-semiconductor field-effect-transistor (MOSFET) was redesigned to ensure reliable probe operation. Fabrication was based on the standard complementary metal-oxide-semiconductor (CMOS) process, and trench formation and the channel definition were modified. Demodulation of the amplitude-modulated drain current was varied, enhancing the signal-to-noise ratio. The I-V characteristics of the inbuilt MOSFET reflect the design and fabrication modifications, and measurement of a buried electrode revealed improved ToGoFET imaging performance. The minimum measurable value was enhanced 20-fold.