Fabian Willems

Dr. Fabian Willems

University of Stuttgart, Stuttgart, Baden-Württemberg, Germany
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 October 2020 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
Fabian WillemsFabian Willems
Fabian Willems
PRPhilip Reitinger
Philip Reitinger
CBChristian Bonten
Christian Bonten
Short fiber reinforced thermoplastics (SFT) are extensively used due to their excellent mechanical properties and low processing costs. Long fiber reinforced thermoplastics (LFT) show an even more interesting property profile and are increasingly used for structural parts. However, their processing by injection molding is not as simple as for SFT, and their anisotropic properties resulting from the fiber microstructure (fiber orientation, length, and concentration) pose a challenge with regard to the engineering design process. To reliably predict the structural mechanical properties of fiber reinforced thermoplastics by means of micromechanical models, it is also necessary to reliable predict the fiber microstructure. Therefore, it is crucial to calibrate the underlying prediction models, such as the fiber orientation model, within the process simulation. In general, these models may be adjusted manually, but this is usually ineffective and time-consuming. To overcome this challenge, a new calibration method was developed to automatically calibrate the fiber orientation model parameters of the injection molding simulation by means of optimization methods. This optimization routine is based on experimentally determined fiber orientation distributions and leads to optimized parameters for the fiber orientation prediction model within a few minutes. To better understand the influence of the model parameters, different versions of the fiber orientation model, as well as process and material influences on the resulting fiber orientation distribution, were investigated. Finally, the developed approach to calibrate the fiber orientation model was compared with a classical approach, a direct optimization of the whole process simulation. Thereby, the new optimization approach shows a calculation time reduced by the factor 15 with comparable error variance.

1 January 2016 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
Fabian WillemsFabian Willems
Fabian Willems
CBC. Bonten
C. Bonten

6 June 2023 in Polymers
Verified
Journal Article
Open access
PDF file
ACAlptekin Celik
Alptekin Celik
Fabian WillemsFabian Willems
Fabian Willems
MTMustafa Tüzün
Mustafa Tüzün
SMSvetlana Marinova
Svetlana Marinova
JHJohannes Heyn
Johannes Heyn
CBChristian Bonten
Christian Bonten
Highly filled plastics may offer a suitable solution within the production process for bipolar plates. However, the compounding of conductive additives and the homogeneous mixing of the plastic melt, as well as the accurate prediction of the material behavior, pose a major challenge for polymer engineers. To support the engineering design process of compounding by twin-screw extruders, this present study offers a method to evaluate the achievable mixing quality based on numerical flow simulations. For this purpose, graphite compounds with a filling content of up to 87 wt.-% were successfully produced and characterized rheologically. Based on a particle tracking method, improved element configurations were found for twin-screw compounding. Furthermore, a method to characterize the wall slip ratios of the compounded material system with different filler content is presented, since highly filled material systems often tend to wall slip during processing, which could have a very large influence on accurate prediction. Numerical simulations of the high capillary rheometer were conducted to predict the pressure loss in the capillary. The simulation results show a good agreement and were experimentally validated. In contrast to the expectation, higher filler grades showed only a lower wall slip than compounds with a low graphite content. Despite occurring wall slip effects, the developed flow simulation for the design of slit dies can provide a good prediction for both low and high filling ratios of the graphite compounds.

1 January 2019 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
Fabian WillemsFabian Willems
Fabian Willems
CBC. Bonten
C. Bonten

30 November 2020 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
PRP. Reitinger
P. Reitinger
Fabian WillemsFabian Willems
Fabian Willems
CBC. Bonten
C. Bonten
The reliable prediction of process-induced fiber microstructure, especially for long fiber reinforced thermoplastics (LFRT), is still a considerable challenge. The prediction by means of computational models with standard settings is not effective and current simulation environments do not allow optimizing the resulting fiber orientation quickly. In case of distinctive anisotropy, the consideration of fiber orientation within the scope of structural mechanics in part design can be considered as indispensable. The basis for an improved prediction is a newly developed optimization approach for an automated calibration of the resulting fiber orientation tensor by means of certain experimental tests. This approach allows optimizing the associated model parameters within a few minutes by calculating a single initial flow field.

30 November 2020 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
Fabian WillemsFabian Willems
Fabian Willems
CBChristian Bonten
Christian Bonten
Short fiber reinforced thermoplastics are used extensively due to their high mechanical properties and low processing costs. Long fiber reinforced thermoplastics (LFT) show an even more interesting property profile and are used more and more often for structural parts. However, processing is not that simple and their anisotropic properties resulting from the fiber microstructure pose a challenge in terms of engineering design process. To reliably predict the structural mechanical properties of LFT, it is necessary to investigate a method that allows comprehensive consideration of the existing fiber microstructure within the engineering design process. For this purpose, a micromechanical approach developed at IKT has been extended to include the necessary process variables and the associated models.