Siti nur liyana mamauod

Dr. Siti nur liyana mamauod

Center of Polymer Composites Research and Technology, Institute of Science, Universiti Teknologi MARA, 40450 Shah Alam, Selangor, Malaysia
+1
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 February 2023 in Polymers
Verified
Journal Article
Open access
PDF file
ZAZafirah Zainal Abidin
Zafirah Zainal Abidin
SMSiti nur liyana mamauod
Siti nur liyana mamauod
ARAhmad Zafir Romli
Ahmad Zafir Romli
SSSiti Salina Sarkawi
Siti Salina Sarkawi
NZNahrul Zainal
Nahrul Zainal
With the rapid development of the palm oil-related industry, this has resulted in the high production of palm oil waste. The increasing amount of palm oil waste has become an alarming issue in which researchers have carried out studies that this palm oil waste has the potential to be used as a biomass source. Carbon black (CB) is the most preferred reinforcing filler in the rubber industry but it has a disadvantage where CB is carcinogenic and a petroleum-based product. Hence CB is less sustainable. Palm kernel shell (PKS) derived from palm oil waste can be turned into palm kernel shell biochar (PKSBc) which can potentially be a value-added, sustainable biofiller as reinforcement in rubber composites. In this study, PKSBc is hybridized with CB (N660) at different loading ratios to be filled in carboxylated nitrile butadiene rubber (XNBR). This study aims to elucidate the effect of the varying ratios of hybrid CB/PKSBc on the rheological properties, abrasion resistance, and hardness of XNBR composites. In this study, both CB and PKSBc are incorporated into XNBR and were then cured with sulphur. The composites were prepared by using a two-roll mill. Different compositions of hybrid CB/PKSBc were incorporated. The rheological properties and physicomechanical properties, such as abrasion resistance and hardness of the vulcanizates, were investigated. Based on the results, as the loading ratio of PKSBc in hybrid CB/PKSBc increases, the cure time decreases, and the cure rate index increases. The abrasion resistance and hardness values of vulcanizates were maintained by the high loading of PKSBc which was due to the porous structure of PKSBc as shown in the morphological analysis of PKSBc. The pores of PKSBc provided mechanical interlocking to reduce volume loss and maintain the hardness of vulcanizates when subjected to force. With this, PKSBc is proven to be a semi-reinforcing filler that could not only act as a co-filler to existing commercialized CB, but PKSBc could also fully substitute CB as reinforcement in rubber, specifically XNBR as it is able to provide high abrasion resistance and hardness to the rubber composites. This would mean the performance of PKSBc is comparable with CB (N660) when it comes to maintaining the physicomechanical properties of XNBR composites in terms of abrasion resistance and hardness. Therefore, this approach of using eco-friendly filler derived from palm oil agricultural waste (PKSBc) can reduce the abundance of palm oil waste, be a sustainable alternative to act as a co-filler in hybrid CB/PKSBc to decrease the usage of CB, and helps to enhance the quality of existing rubber-based products.

1 January 2021 in Journal of the Mechanical Behavior of Materials
Verified
Journal Article
Open access
PDF file
ZAZafirah Zainal Abidin
Zafirah Zainal Abidin
SMSiti nur liyana mamauod
Siti nur liyana mamauod
DKDarren Khooi
Darren Khooi
SSSiti Salina Sarkawi
Siti Salina Sarkawi
HIHanafi Ismail
Hanafi Ismail
Rising environmental issues and huge disposal of rubber waste have resulted in an increased interest in the usage of reclaimed rubber (RR) to produce sustainable and environmental friendly applications. In this study, incorporation of butyl reclaimed rubber into carboxylated nitrile butadiene rubber (XNBR/BRR) was carried out where the loadings of each XNBR and BRR were varied. The rubber was cured with sulphur during the melt mixing using a two-roll mill. This study is aimed to investigate the applied BRR loading towards the physical and mechanical properties of the XNBRcompounds. The results appeared that the optimum cure time (T90) increased and curing rate index (CRI) showed that a faster curing reaction with the increase in the content of BRR where the T90 had an increment of 89% while the CRI was faster by 89%. As for the crosslink density which indicates the density of chains or segments in polymer network, it decreased about 20% with increasing level of BRR. Also, the compression set which refers to the ability of rubber to resist permanent deformation, had an increase of 73% as the loading ratio of BRR increased. These results were obtained due to the low molecular weight of the BRR where the high shear and temperature during the reclamation process severely breaks down the molecular chains of the BRR into shorter segments. With the results obtained, it is shown that reclaimed rubber has the potential for further development and could increase the interest of researchers all around the world in the incorporation of reclaimed rubber for footwear application.

17 June 2020 in BioResources
Verified
Journal Article
Closed access
ZAZafirah Zainal Abidin
Zafirah Zainal Abidin
SMSiti nur liyana mamauod
Siti nur liyana mamauod
SSSiti Salina Sarkawi
Siti Salina Sarkawi
NSNurshamimi Shahirah Binti Saimi
Nurshamimi Shahirah Binti Saimi
This research aimed to elucidate the effect of black and non-black filler systems on the cure characteristics and mechanical properties of butyl reclaimed rubber (BRR). In this study, BRR800 was the BRR investigated. Since reclaimed rubber is not entirely 100% rubber, actually being a mixture of rubber, carbon black, oil, zinc oxide, stearic acid and other compounding ingredients used in the original compounds, the reclaimed rubber content in each system was fixed at 161 parts per hundred (pphr). Each mixture was mixed using a two-roll mill. The fillers used in this study were carbon black and calcium carbonate. The Mooney viscosity, cure characteristics, crosslink density, and mechanical properties, such as hardness, abrasion resistance, compression set, tear strength, rebound resilience, and the tensile properties of the vulcanizates were investigated. The results showed that the Mooney viscosity of BRR800 filled with carbon black was increased effectively and had a faster curing time and higher crosslink density than BRR filled with calcium carbonate. In addition, except for compression set and elongation at break, the mechanical properties of BRR800 with a black filler system were higher than those of BRR800 with a non-black filler system.

31 January 2023 in Journal of Electrochemical Energy Conversion and Storage
Verified
Journal Article
Closed access
PDF file
RFRoslinda Fauzi
Roslinda Fauzi
RDRusli Daik
Rusli Daik
BFBasirah Fauzi
Basirah Fauzi
SMSiti nur liyana mamauod
Siti nur liyana mamauod
Ionic liquids (ILs) that are used in the market nowadays have high complexity of processing, high viscosity, and high toxicity in comparison to deep eutectic solvent (DES). Deep eutectic solvent is typically used in thermal energy storage, separation and extraction process or electrochemistry field. This study focuses on determining the physicochemical properties of DES, which are thermal conductivity, viscosity, and surface tension. DES was prepared by mixing hydrogen-bond donor (HBD) compounds (ethylene glycol) and hydrogen-bond acceptor (HBA) compounds (N,N-diethylethanolammonium chloride) at different molar compositions. The data show that the molar ratio HBA:HBD of 1:2 resulted in optimized values of thermal conductivity (0.218 W/mK), low viscosity (38.1 cP), and high surface tension (54 mN/m). Most notably, DES is capable of sustaining in a liquid phase at ambient condition (25 °C) for more than 30 days. Fourier transform infrared spectrum did not indicate any presence of a new peak. This established that only delocalization of ions occurred, and hence, chemical transformations did not take place during mixing. The data obtained showed that the newly synthesized solvent (DES) possess better result than the ILs. Therefore, DES can be proposed to replace the dependency on ILs.

1 February 2025 in BioResources
Verified
Journal Article
Closed access
MAMohammad Tahar Nur ‘aIsyah Ar-Raudhoh
Mohammad Tahar Nur ‘aIsyah Ar-Raudhoh
MHMohd Fadzli Muhamad Haziq
Mohd Fadzli Muhamad Haziq
SMSiti nur liyana mamauod
Siti nur liyana mamauod
NZNahrul Zainal
Nahrul Zainal
The rapid growth in Malaysia’s oil palm industry has resulted in the increase in production of palm oil and oil palm waste such as palm kernel shell (PKS). However, the lack of awareness on the beneficial value of these wastes has led to sustainability issues. Thus, PKS can be converted into biochar (PKSB) and can be used as a potential bio-filler. The PKSB was produced in sizes ranging from micro to nano using a high energy ball mill (HEBM) to be used as a filler in natural rubber (NR) vulcanizates. This study evaluated the effects of varying n-PKSB loadings (0 to 10 phr) on the cure characteristics, bound rubber content (BRC), swelling, tensile, and abrasion properties of the NR vulcanizates. Results showed that n-PKSB-filled NR vulcanizates had lower minimum torque (ML) and cure rate index (CRI), along with improved BRC and crosslink density as the filler concentrations increased. The optimum loading ratio was 5 phr (F4), as this formulation offered the best mechanical properties and more homogenous dispersion of n-PKSB compared to other loadings. The overall performance of F4 showed high crosslink density (7.82 x 10-5 mol/cm3), BRC (3.94%), tensile strength (17 MPa), abrasion resistance (32.37%), and lower EB (451%). Overall, n-PKSB has great potential as bio-filler, addressing oil palm waste issues and benefiting the industry.