This study focused on investigating the bottoming power cycles operating with CO2-based binary mixture, taking into account exergetic, economic and exergo-environmental impact indices. The main intent is to assess the benefits of employing a CO2-based mixture working fluid in closed Brayton bottoming power cycles in comparison with pure CO2 working fluid. Firstly, selection criteria for the choice of suitable additive compound for CO2-based binary mixture is delineated and the composition of the binary mixture is decided based on required cycle minimum temperature. The decided CO2-C7H8 binary mixture with a 0.9 mole fraction of CO2 is analyzed in two cycle configurations: Simple regenerative cycle (SRC) and Partial heating cycle (PHC). Comparative analysis among two configurations with selected working fluid are carried out. Thermodynamic analyses at varying cycle pressure ratio shows that cycle with CO2-C7H8 mixture shows maximum power output and exergy efficiency at rather higher cycle pressure ratio compared to pure CO2 power cycles. PHC with CO2-C7H8 mixture shows 28.68% increment in exergy efficiency with the levelized cost of electricity (LCOE) 21.62% higher than pure CO2 PHC. Whereas, SRC with CO2-C7H8 mixture shows 25.17% increment in exergy efficiency with LCOE 57.14% higher than pure CO2 SRC. Besides showing lower economic value, cycles with a CO2-C7H8 mixture saves larger CO2 emissions and also shows greater exergo-environmental impact improvement and plant sustainability index.
The construction industry is known for poor performance, low productivity, high waste generation, and for lagging in the adoption of new technology. A high rate of material wastage in construction projects has economic and environmental implications for concerned stakeholders. Construction waste quantification is an essential requirement for formulating waste management strategies. Technological advancements like building information modeling (BIM) and artificial intelligence (AI) provide effective solutions to the construction industry to deal with these prevalent issues. This literature review-based study observes the scarcity of research on the application of BIM in construction waste quantification. The limited number of studies found in the literature confirm the ability of BIM-aided waste quantification models to forecast waste generation. Moreover, the application of these models can also assist in reducing waste to a considerable extent. This study recommends that further studies should be conducted on technology-assisted waste quantification in building and infrastructure projects to evaluate their effectiveness for subsequent implementation in the industry.
28 January 2020 in International Journal of Energy Research
Technologically advanced countries are accruing benefits from the adoption of Building Information Modelling (BIM) in the Architecture, Engineering, and Construction (AEC) industry after decades of struggling for productivity enhancement using innovation and automation. Most of the developing countries have not been able to embrace technology in the AEC Sector and, consequently, are unable to ameliorate prevalent performance-related issues in construction projects. This review article identifies hurdles to BIM implementation in selected developing countries via an examination of the latest studies. The most significant challenges observed in this study are Lack of Training for Professionals, Lack of Awareness, Huge Capital Cost, Resistance to Change, and Complexity of BIM Software. This study is an update on previous studies conducted with the aim of assisting the implementation of BIM in developing countries.
The temperature gradient of the top and bottom layers of sea water can be employed for power generation through ocean thermal energy conversion cycles (OTEC). In this thermodynamic study, an organic Rankine cycle is used to convert the ocean thermal energy of the Arabian sea into useful electrical power. A comparative investigation is carried out between R152a and R1234yf working fluids. Sensitivity analysis is performed at varying condenser saturation temperatures and evaporator saturation temperatures. For the R152a OTEC cycle, 2.8% thermal efficiency, 47.9% exergy efficiency and 9064 W turbine work are obtained at the optimum point. Similarly, for the R1234yf working fluid in the OTEC cycle, 2.8% thermal efficiency, 46.9% exergy efficiency and 4818 W turbine work are obtained at the optimum point.
Owing to high energy-intensive operations, cement production is responsible for global 6–8% of CO2 emissions and, thus, can be a major contributor in the net zero mission. Pakistan’s cement industry can produce 69 million tons of cement per year and has an overall share of 5.3% in economy. One ton of cement production releases approximately one ton of carbon dioxide. Therefore, it is necessary to decarbonize this industry. Two strategies can be employed (waste heat utilization and CO2 capturing) for the decarbonization of the cement industry. This comprehensive review article is focused on the waste heat recovery potential and the technologies employed to utilize this potential for the cement industry of Pakistan.