With the increasing trend of high-rise, large-scale, and functional modern architectural structures, lightweight aggregate (LWA) concrete that exhibits excellent strength and high functionality has garnered active research attention. In particular, as the properties of concrete vary considerably with the raw materials and the proportions of aggregates in the mix, in-depth research on weight reduction, strength improvement, and functional enhancements of aggregates is crucial. This study used the negative pressure coating of a mixed solution comprising epoxy (mixture of epoxy resin and crosslinker), hyper-crosslinked polymer, and titanium oxide (TiO₂) nanoparticles on the LWA, and achieved an improvement in the strength of the LWA as well as a reduction in air pollutants such as NO_x and SO_x. Compared to a normal LWA with an aggregate impact value (AIV) of 38.7%, the AIV of the proposed epoxy–TiO₂-embedded high-strength functional LWA was reduced by approximately half to 21.1%. In addition, the reduction rates of NO_x and SO_x gases resulting from the photocatalytic properties of TiO₂ nanoparticles coated with epoxy were approximately 90.9% and 92.8%, respectively. Epoxy–TiO₂, embedded in LWAs through a mixture, exhibited stability, high strength, and a reduction in air pollutant characteristics, despite repeated water washing. The LWA proposed herein offers excellent structural and functional properties and is expected to be used in functional lightweight concrete that can be practically applied in high-rise and large-scale architectural structures.

Polydimethylsiloxane (PDMS), an optically transparent and inert material, is widely used in biological and semiconductor applications owing to its excellent chemical stability and moldability. This study proposes a thermally induced wet spinning method for the fabrication of long PDMS fibers with a constant width. PDMS is a thermoset polymer that undergoes chemical crosslinking when heated, and the thermally induced wet spinning process allows for the formation of fibers without a mold. A rapid thermal curing step was used to instantly solidify the thermoset polymer, where immediate chemical crosslinking of fluid PDMS solution was achieved upon contact with an oil coagulation bath at 180–230 °C. A rapid stretching process was applied to pull out and control the width of the fiber, and the PDMS was stretched at a rate of 1.2–12.5 m/min during the crosslinking process. The fabricated pristine PDMS fibers were transparent and maintained a crosslinked network with excellent mechanical strength. In addition, the PDMS fibers were functionalized with silica nanoparticles, carbon nanotubes, and pores to adjust their transparency/opacity, conductivity, and heat insulation properties, respectively, for various applications. The proposed thermally induced wet spinning method shows promise for overcoming the limitations of existing molding methods, in which the PDMS fibers cannot be lengthened. Furthermore, the process is environmentally friendly and economical owing to the use of edible canola oil, which reduces the volume of harmful solvents and additives during fiber production.

A wearable sensor is fabricated using a highly elastic and hydrophobic color-changing fiber that embeds thermochromic materials into a silica aerogel, and works stably against water, sweat, and detergent solutions.

Flexible fibers composed of a conductive material mixed with a polymer matrix are useful in wearable electronic devices. However, the presence of the conductive material often reduces the flexibility of the fiber, while the conductivity may be affected by environmental factors such as water and moisture. To address these issues, we developed a new conductive fiber by mixing carbon nanotubes (CNT) with a polyurethane (PU) matrix. A silane ((heptadecafluoro–1,1,2,2–tetra–hydrodecyl)trichlorosilane) was added to improve the strain value of the fiber from 155% to 228%. Moreover, silica aerogel particles were embedded on the fiber surface to increase the water contact angle (WCA) and minimize the effect of water on the conductivity of the fiber. As a result, the fabricated PU-CNT-silane-aerogel composite microfiber maintained a WCA of ~140° even after heating at 250 °C for 30 min. We expect this method of incorporating silane and aerogel to help the development of conductive fibers with high flexibility that are capable of stable operation in wet or humid environments.

The sensor, designed to be worn directly on the skin, is suitable for real-time monitoring of the recovery level of not only general wounds, but also difficult-to-heal wounds, such as those with chronic inflammation. Notably, healthy skin has a pH range of 4–6. When a wound occurs, the pH is known to be approximately 7.4. In this study, alpha-naphtholphthalein (Naph) was immersed in a cotton-blended textile to produce a wearable halochromic sensor that clearly changed color depending on the pH of the skin in the range 6–9, including pH 7.4, which is the skin infection state. The coating was performed without using an organic solvent by dissolving it in micelle form using cetyltrimethylammonium bromide, a surfactant, in water. Naph-based halochromic sensor shows light yellow, which is the dye’s own color, at pH 6, which is a healthy skin condition, and gradually showed a clear color change to light green-green-blue as pH increased. Even after washing and drying by rubbing with regular tap water, the color change due to pH was maintained more than 10 times. Naph-based halochromic sensors use a simple solution production and coating method and are not only reusable sensors that can be washed with water but also use environmentally friendly water, making them very suitable for developing commercial products for wound pH monitoring. In addition, it can be easily applied to medical supplies, such as medical gauze, patient clothes, and compression bandages, as well as everyday wear, such as clothing, gloves, and socks. Therefore, it is expected to be widely used as a wound pH sensor, allowing real-time monitoring of the skin condition of individuals with chronic skin inflammation, including patients requiring wound recovery.