Face masks are loose-fitting masks that cover the nose and mouth and have ear ties at the back of the head whereas respirators are tight-fitting face covering devices which filter the air during inhalation and exhalation. Guidelines issued by the US Centers for Disease Control and Prevention (CDC) regarding proper design, filtration process and wearing should be followed. The mask equipment provides protection against the infections caused by particulate matters (PM), especially PM2.5, and biological pathogens such as bacteria and viruses. Although face masks offer benefits to a greater extent, it is not recommended to wear them for a long period of time. As N95 masks closely fit with the face, it may result in negative impact on respiratory and dermal mechanisms of human thermoregulation. In this article, currently available face masks including cloth masks, their filtration mechanisms, manufacturing methods and decontamination methods are reviewed for the purpose of helping with the coronavirus pandemic (COVID-19).
Fused Deposition Modeling (FDM) is an extrusion type additive manufacturing (AM) method in which a molten polymer is selectively extruded in layer-by-layer manner. Although there are several other AM techniques, FDM is a suitable method to produce fabric structures as it is capable of processing polymers and is widely used in various engineering applications. This article summarizes the current research works in characterization of FDM parts, advancements in materials used in FDM and latest works related to making fabric samples using FDM. The results show that the mechanical properties and surface quality are compromised in FDM parts. Strength and flexibility with better surface finishing are essential parameters in fabric structures. There are mainly two techniques that are explored by researchers to enhance the quality of the parts. The first is optimizing process parameters and the second is improving material quality. FDM process parameters like extrusion temperature, layer height, print speed and built orientation can significantly influence the quality of the parts. Optimizing these parameters can significantly enhance the strength of the fabric produced. Moreover, a great amount of impetus is given to improve material by reinforcing it and making polymer blends with specific qualities. There has been studies related to the development of fabric structures and deposition of polymers on fabrics with FDM. It is concluded that the major concern with such structures is strength and processability. To address these issues, optimizing process parameters and developing new filaments for exclusively making fabrics can be the future work in this area.
2 December 2021 in Journal of Thermoplastic Composite Materials
Polylactic acid and thermoplastic polyurethane (TPU) were mixed in different proportions and extruded through twin-screw and single screw extruders to obtain composite filaments to be used for additive manufacturing (3D printing) with fused deposition modeling method. The properties of the filaments were characterized using uniaxial tensile tests, differential scanning calorimetry, thermogravimetric analysis, Fourier transform infrared spectroscopy, rheology, polarized optical microscope, and scanning electron microscope. 3D printed samples from composite filaments were tested using dynamic mechanical analysis. It was found that the tensile strength and modulus of the filaments decrease while elongation at break increases with the increasing TPU content in the composite. The analysis also showed a partial miscibility of the polymer constituents in the solution of composite filaments. Finally, a flexible structure, plain weave fabric, was designed and 3D printed using the composite filaments developed which proved that the filaments are well suited for 3D printing.
Various types of additive manufacturing (AM) methods (also called 3D printing), and materials have been increasingly studied in the field of additive manufacturing of flexible structures such as fabrics, and flexible electronics. Polymer-based AM processes allow the flexibility, rapid, and low-cost fabrication of complex geometries depending on the types of materials used. The purpose of this review article is to summarize the major AM methods, materials, and their emerging applications to additively manufacture the flexible structures. In the AM methods section, Fused Deposition Modeling (FDM), and Selective Laser Sintering (SLS) are reviewed for fabrics, and Direct Ink Writing (DIW) for electronics. In the Materials section, the manufacturing methods, chemical structures, properties, advantages, and limitations of some of the widely used materials in three-dimensional (3D) printing of polymers are reviewed. Third, the applications of these methods and materials for fabrics, and electronics are covered. Finally, the associated opportunities and challenges in 3D printing process of flexible structures are described. The future research should be related to the exploration of combinations and development of innovative materials, printing process parameters, detail study on improving the properties, and hybrid 3D printing process.
Electrospinning was used to make activated carbon nanofibers with polyacrylonitrile (PAN) as the precursor. The applied voltage was found to be more influential on electrospun PAN fiber diameters than the flow rate and needle tip-collector distance. Tensile load and tear strength of electrospun PAN membranes increased with thickness, accompanied with a decrease in air permeability; however, burst strength was not significantly influenced by the thickness. Electrospun PAN nanofiber membranes were stabilized in air and then activated at 800°C with KOH as the activating agent to make activated carbon nanofibers. Stabilized PAN membranes showed different breaking behaviors from those before stabilization. The maximum tensile stress of the stabilized PAN membranes from different concentrations was affected differently by the stabilization process. The resulting activated carbon nanofibers had no C ≡ N bond. The activation process generated micropores which contributed to a large surface area of 936.2 m2/g and a micropore volume of 0.59 cc/g. Pore size distributions of electrospun PAN and activated carbon nanofibers were analyzed based on the Dubinin-Astakhov equation and the generalized Halsey equation. The results showed that activated carbon nanofibers had many more micropores than electrospun PAN, increasing their potential applications in adsorption.
In this study, monofilament tubular braided structures were fabricated and their performances were analyzed. The braided tubes are in three-dimensional form, made of polyester monofilaments intended for use in medical applications. This type of structure, called a stent, is used to open clogged arteries and veins by exerting radial forces. The radial force of a braided tube basically depends on three variables: braid angle, helical length, and braid diameter. The mandrel diameter influences the axial and radial forces obtained from the braid tube. In order to assure a stable structure, the braided fabrics were heat-set. Analysis of variances showed that heat-setting temperatures and heat-setting times of braided fabrics exhibited no significant effects in the range in which the tests were performed.