Pneumatic artificial muscles (PAMs) are one of the key technologies in soft robotics, and they enable actuation in mobile robots, in wearable devices and exoskeletons for assistive and rehabilitative purposes. While they recently showed relevant improvements, they still present quite low payload, limited bandwidth, and lack of repeatability, controllability and robustness. Vacuum-based actuation has been recently demonstrated as a very promising solution, and many challenges are still open, like generating at the same time a large contraction ratio, and a high blocking force with enhanced axial stiffness. In this paper, a novel Ultralight Hybrid PAM (UH-PAM), based on bellow-type elastomeric skin and vacuum actuation, is presented. In particular, open-cell foam is exploited as a structural backbone, together with plastic rings, all embedded in a thin skin. The design and optimization combine numerical, analytical, and experimental data. Both static and dynamic analysis are performed. The weight of the optimized actuator is only 20 g. Nevertheless, a contraction ratio up to 50% and a maximum payload of 3 kg can be achieved. From a dynamic point of view, a rise time of 0.5 s for the contraction phase is observed. Although hysteresis is significant when using the whole contraction span, it can be reduced (down to 11.5%) by tuning both the vacuum range and the operating frequency for cyclic movements. Finally, to demonstrate the potentiality of this soft actuation approach, a 3 DoFs Stewart platform is built. The feasibility of performing smooth movements by exploiting open-loop control is shown through simple and more complex handwriting figures projected on the XY plane.
Although natural continuum structures, such as the boneless elephant trunk, provide inspiration for new versatile grippers, highly deformable, jointless, and multidimensional actuation has still not been achieved. The challenging pivotal requisites are to avoid sudden changes in stiffness, combined with the capability of providing reliable large deformations in different directions. This research addresses these two challenges by harnessing porosity at two levels: material and design. Based on the extraordinary extensibility and compressibility of volumetrically tessellated structures with microporous elastic polymer walls, monolithic soft actuators are fabricated by 3D printing unique polymerizable emulsions. The resulting monolithic pneumatic actuators are printed in a single process and are capable of bidirectional movements with just one actuation source. The proposed approach is demonstrated by two proof‐of‐concepts: a three‐fingered gripper, and the first ever soft continuum actuator that encodes biaxial motion and bidirectional bending. The results open up new design paradigms for continuum soft robots with bioinspired behavior based on reliable and robust multidimensional motions.
The rapid development of unmanned aerial vehicles (UAVs) has helped expand their practical use to many industrial applications. However, UAVs sometimes suffer from a flight time limitation and/or a loss in communication. Such undesired malfunctions can endanger public safety and incur economic losses. This paper presents a new class of UAV that can retrieve a disabled or malfunctioned UAV from the ground. We developed a deployable hook retrieval system (DHRS) which integrates three principal mechanisms (i.e., deployment, slider-linkage-release, and hook release). Each mechanism plays a role in deploying and retrieving multiple hooks while using a simple control strategy. Through a Finite Element Method simulation, the hook was topologically optimized in order to achieve a high strength while reducing weight. The deployed multiple hooks allow the device to capture the target regardless of its orientation. Due to these design strategies, object recognition using a computer vision was simply demonstrated by exploiting ORB and FLANN algorithms. Through an experimental study, we discussed the target range, success rate, and the practical uses that the DHRS could achieve. The results show that the proposed designs were versatile and consistently successful in capturing the targets while addressing constraints such as power consumption, computational load, and lack of prior knowledge or information about the target.
For earth observation, the optical systems in small satellites are crucial to obtain high- resolution images. However, the alignment between a primary and a secondary mirror in an optical system can be disturbed due to the harsh environments inside vehicles or space (i.e., vibrations, shock loading during launch, dramatic temperature changes, or high vacuum pressure in space). To compensate for such undesired deformations, a focusing mechanism should be embedded into the optical system. In this paper, we propose a novel Single Motor-Driven Focusing mechanism with Flexure Hinges (SMFH), allowing the Flexure Hinge (FlexHe) to displace in the longitudinal direction. The presented FlexHe incorporates radial zig-zag-patterned slits to achieve flexibility, and preloading of the hinge structures to reduce the resulting hysteresis. To investigate an optimal configuration of FlexHe, a numerical simulation is performed by means of ANSYS 19.2. The variation of Modulation Transfer Function (MTF), corresponding to an image resolution, is evaluated by using an optics simulation program (CODE-V). The experimental setups are built by exploiting the fabricated SMFH and five LVDT (Linear Variable Differential Transformer) sensors with a high resolution of 0.031 µm. As a result, hysteresis can be reduced up to 6.52% with a pre-stretched length of 3 µm. The proposed SMFH allows not only the De-space to displace up to 23.93 µm, but also the De-center and the Tilt to achieve the desired displacements of 5.20 µm and 88.45 µrad, respectively. Conclusively, the SMFH shows promising characteristics to embed a feedback control, due to its high resolution (up to 0.1 µm) for De-space with the MTF of 37%.
Perception in soft robotics is crucial to allow a safe interaction to effectively explore the environment. Despite the inherent capabilities of soft materials, embedding reliable sensing in soft actuators or robots could introduce constraints in the overall design (e.g., loss of deformability, undesired trajectories, etc.) or reduce their compliant characteristics. Consequently, an adequate stiffness for both sensor and actuator becomes a crucial design parameter. In particular, for sensing the deformation related to actuation motion, sensing and actuating strategies must work in full mechanical synergy. In this view, an inductive sensing solution is presented, exploiting open-cell foam and a copper (Cu) wire in an Inductive Foam Sensor (IFS). Due to entangled air cells high deformability is enabled upon vacuum pressure, and proprioceptive information is provided. The IFS is then successfully integrated into the earlier developed Ultralight Hybrid Pneumatic Artificial Muscle (UH-PAM), which encases an elastomeric bellow skin and plastic rings. Such sensorized UH-PAM (SUH-PAM) is capable of a high contraction ratio (54% upon −80 kPa), while the inductive sensing shows a high sensitivity of 0.01031/1% and a hysteresis of 5.35%, with an average error of 1.85%, respectively. In order to implement a robust feedback control system, an adaptable proportional sliding mode control is presented. As a result, the SUH-PAM motion can be controlled to the mm-scale, with an RMSE of 0.925 mm, and high robustness against disturbances is demonstrated.