An important problem that arises at present refers to the increase in performances in the exploitation of the conveyor belts. Additionally, it is pursued to use some materials, which can be obtained by recycling rubber and PVC waste, in their structure. Thus, the research aimed at creating conveyor belts using materials obtained from the recycling of rubber and PVC waste. Under these conditions, conveyor belts were made that had in their structure two types of rubber and PVC, which was obtained by adding in certain proportions of reclaimed rubber and powder obtained from grinding rubber waste. In order to study the effect of adding PVC on properties, four types of conveyor belts were made, with the structure of rubber, PVC and textile reinforcement. These have been subjected to certain mechanical tests, also being analyzed from the point of view of the behavior of the accelerated aging. The results obtained showed that the addition of PVC lead to a decrease in tensile stress for the strips made, but also an increase in the tensile strain. Additionally, the elasticity tests performed before and after the accelerated aging showed that the presence of PVC in the structure of the conveyor belts determined a substantial reduction of the aging process of the rubber in the conveyor belts. Under these conditions, it has been established that the use of PVC in the structure of rubber matrix conveyor belts is beneficial if conveyor belts are to be produced that are less subject to mechanical stress, but that work in conditions that can cause accelerated aging of materials. An analysis with the finite element method (FEM) of the test samples was also performed.

Using aluminium metal matrix nanocomposites has recently gained increased attention in the industry due to their high strength and ductility. In this paper, TiO₂ nanoparticles in volume percentages of 5 wt. % were added to the AA2024 alloy using the stir casting method. Using a novel powder injection system, TiO₂ nanoparticles with an average particle size of 30 ± 5 nm was added to the matrix. The influence of TiO₂ content on the fatigue life before and after heat treatment was studied. The results showed the fatigue properties of AA2024 with TiO₂ nanoparticles increased after heat treatment. The optimum improvement in fatigue properties was obtained at 5 wt. % TiO₂ after heat treatment, with an improving fatigue life in 14.71% compared with sample based. This is due to an increased number of fine precipitates besides its uniformly distributed after heat treatment. The fatigue life of the composite materials with added nanoparticles was investigated using a finite element-based ANSYS workbench. There was a good match between what happened in the experiments and what happened to the numerical fatigue strength. For the composite materials, the difference between the experimental and numerical values of fatigue strength was not greater than 4% for the matrix. The results also, indicated that, after ageing, the precipitate-free zone at the inter-dendritic zone disappeared or became smaller. However, after adding 5 wt. % of titanium and, also, performing heat treatment, it is not possible to precipitate the Al₂CuMg precipitates, and, instead of it, the Al₃TiCu and Al₇TiCu phases precipitates have been formed.

Background and objectives: Osteoporotic spine fractures represent a significant factor for decreasing quality of life in the elderly female population. Understanding the mechanisms involved in producing these fractures can improve their prevention and treatment. This study presents a biomechanical method to produce a vertebral fracture, conducted on a human spine segment, observing the displacements and strains in the intervertebral disc, endplate, and vertebral body. Materials and Methods: We performed two tests, one corresponding to an extension loading, and the second to an axial loading. Results: The maximum displacement in the target vertebral body presented higher values in the case of the extension as compared to the axial strain where it mainly occurred after the fracture was produced. The strains occurred simultaneously on both discs. In the case of the axial strain, due to the occurrence of the fracture, the maximum value was recorded in the spine body, while in the case of the extensions, it occurred in the neural part of the upper disc. The advantage of this method was that the entire study was an experiment, using optical methods, increasing the precision of the material data input. Conclusions: The research method allowed recording in real time of a larger amount of data from the different components of the spine segment. If there was an extension component of the compression force at the moment of the initial loading, part of this load was absorbed by the posterior column with higher mechanical resistance. After the maximum capacity of the absorption was reached, in both situations the behavior was similar.

Polymeric materials are increasingly used in the automotive industry, aeronautics, medical device industry, etc. due to their advantage of providing good mechanical strength at low weight. The incremental forming process for polymeric materials is gaining increasing importance because of the advantages it offers: relatively complex parts can be produced at minimum cost without the need for complex and expensive dies. Knowing the main strains and especially the thickness reduction is particularly important as it directly contributes to the mechanical strength of the processed parts, including in operation. For the design of experiments, the Taguchi method was chosen, with an L₁₈ orthogonal array obtained by varying the material on two levels (polyamide and polyethylene) and the other three parameters on three levels: punch diameter (6 mm, 8 mm and 10 mm), wall angle (50°, 55° and 60°) and step down (0.5 mm, 0.75 mm and 1 mm). The output parameters were strain in the x direction, strain in the y direction, major strain, minor strain, shear angle and thickness reduction. Two analyses were conducted: signal-to-noise ratio analysis with the smaller-is-better condition and analysis of variance. The optimum values for which the thickness was reduced were the following: wall angle of 50°, punch diameter of 10 mm and step down of 0.75 mm.

Using antibiotic impregnated cement is an important mean to treat and prevent periprostetic joint infections. This complication requires for treatment important financial and technical resources. Adding antibiotics to orthopaedic cement may alter its mechanical properties with possible reduced time of prosthesis survival rate. This study analyze the mechanical properties of cement mixed with antibiotics in the operation room, which helps reducing costs and permit a more specific antibiotic local therapy. All tested antibiotics used in this study does not change the mechanical behavior of the orthopaedic cement when mixed in therapeutic doses, all alterations seems to be at a level below clinical significance. Mixing antibiotics in Orthopedic cement leads to minor decrease of the mechanical properties for cefazolin, cefuroxime, ceftazidime, meropenem and vancomycin and a mechanical significant decrease for gentamicin and clindamycin.

Machining processes through cutting are accompanied by dynamic phenomena that influence the quality of the processed surfaces. Thus, this research aimed to design, make, and use a tool with optimal functional geometry, which allowed a reduction of the dynamic phenomena that occur in the cutting process. In order to carry out the research, the process of cutting by front turning with transversal advance was taken into account. Additionally, semi-finished products with a diameter of Ø = 150 mm made of C45 steel were chosen for processing (1.0503). The manufacturing processes were performed with the help of two tools: a cutting tool, the classic construction version, and another that was the improved construction version. In the first stage of the research, an analysis was made of the vibrations that appear in the cutting process when using the two types of tools. Vibration analysis considered the following: use of the Fast Fourier Transform (FFT) method, application of the Short-Time Fourier-Transformation (STFT) method, and observation of the acceleration of vibrations recorded during processing. After the vibration analysis, the roughness of the surfaces was measured and the parameter Ra was taken into account, but a series of diagrams were also drawn regarding the curved profiles, filtered profiles, and Abbott–Firestone curve. The research showed that use of the tool that is the improved constructive variant allows accentuated reduction of vibrations correlated with an improvement of the quality of the processed surfaces.