Corrosion behaviour of AZ and ZA magnesium alloys in untreated, aerated, and deaerated chloride media was investigated. The influence of impurity, alloying element, and oxygen on corrosion potential, rate, and pitting was examined in alkaline media saturated with Mg(OH)2at pH 9 and 25°C. After 8 h immersion, slightly less active corrosion potentials were generally observed in deaerated than oxygen containing solutions. AZ91D and ZA104 alloys recorded much lower corrosion rates in deaerated medium as compared to AZ91E, ZAC 10403 (0.3Ca), and ZACS1040305 (0.3Ca+ 0.5Sr). Generally, ZAC alloy showed the highest corrosion rate, followed by ZACS alloy, and both showed a constant value in the three media with or without oxygen. The effect of oxygen is then dependent on the alloy properties and is not a simple acceleration of the cathodic reaction but could cause also inhibition and/or passivation. Pit depth and distribution were influenced by alloy composition. The pits were found deeper and more localized on AZ and more uniformly dispersed on ZA alloy surfaces.
23 November 2011 in Plasma Chemistry and Plasma Processing
Purpose: Transplantation of autologous and/or allogeneic blood vessels is the most convenient treatment for vascular diseases. With regard to extensive need for blood vessels, developments in vascular tissue engineering are contributing greatly. In this study, our aim is to create intact small-diameter tubular vascular grafts cultivated in pulsatile flow bioreactor. Materials and Methods: CD146+ cell-based small-diameter vascular grafts were fabricated with ECM/glycosaminoglycans and polyurethane nanofibers. Characterization of the vascular graft was performed by SEM and WST-1. To mimic blood circulation in the bioreactor, human CD34+ cells cultured in megakaryocytes/platelets medium; then these cells were transferred inside of the vascular graft to mimic blood circulation. Cell differentiation was evaluated by flow cytometry and colony assay. Wright-Giemsa staining and polyploidy analysis were performed to show the differentiated cell population inside of the vascular graft. Anti-thrombogenic properties of the blood vessel were demonstrated by IF. Results: Polyurethane nanofibers provided a suitable environment for Human umbilical cord vein endothelial cells (HUVECs), and no significant cytotoxic effect was observed. Scanning electron microscopy (SEM) analysis of the tubular graft showed that under perfusion HUVECs, smooth muscle cells (SMCs) and fibroblasts formed layers that aligned on each other, respectively. The vascular graft was strong with a tensile strength of 0.70 MPa and elastic modulus of 0.007 GPa. When cultured in a bioreactor system, platelet adhesion to the vascular graft was remarkably low. Conclusion: In conclusion, this vascular graft may hold the potential to regenerate functional small-diameter vessels for cardiovascular tissue repair.
28 April 2021 in Journal of Thermoplastic Composite Materials
Polyetheretherketone (PEEK) and its composites are commonly used in the industry. Materials with PEEK are widely used in aeronautical, automotive, mechanical, medical, robotic and biomechanical applications due to superior properties, such as high-temperature work, better chemical resistance, lightweight, good absorbance of energy and high strength. To enhance the tribological and mechanical properties of unreinforced PEEK, short fibers are added to the matrix. In this study, Artificial Neural Networks (ANNs) and the Adaptive-Neural Fuzzy Inference System (ANFIS) are employed to predict the cutting forces during the machining operation of unreinforced and reinforced PEEK with30 v/v% carbon fiber and 30 v/v% glass fiber machining. The cutting speed, feed rate, material type, and cutting tools are defined as input parameters, and the cutting force is defined as the system output. The experimental results and test results that are predicted using the ANN and ANFIS models are compared in terms of the coefficient of determination ( R2) and mean absolute percentage error. The test results reveal that the ANFIS and ANN models provide good prediction accuracy and are convenient for predicting the cutting forces in the turning operation of PEEK.