Joshua Adeniyi Depiver

Dr. Joshua Adeniyi Depiver

Mechanical and Manufacturing, University of Derby, Derby, UK
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2021 in Engineering Failure Analysis
Verified
Journal Article
Closed access
JDJoshua Adeniyi Depiver
Joshua Adeniyi Depiver
SMSabuj Mallik
Sabuj Mallik
EAEmeka H. Amalu
Emeka H. Amalu

5 November 2020 in Journal of Electronic Materials
Verified
Journal Article
Open access
PDF file
JDJoshua Adeniyi Depiver
Joshua Adeniyi Depiver
SMSabuj Mallik
Sabuj Mallik
EAEmeka H. Amalu
Emeka H. Amalu
Ball grid array (BGA) packages have increasing applications in mobile phones, disk drives, LC displays and automotive engine controllers. However, the thermo-mechanical reliability of the BGA solder joints challenges the device functionality amidst component and system miniaturisation as well as wider adoption of lead-free solders. This investigation determines the effective BGA solders for improved thermo-mechanical reliability of the devices. It utilised a conducted study on creep response of a lead-based eutectic Sn63Pb37 and four lead-free Tin–Silver–Copper (SnAgCu) [SAC305, SAC387, SAC396 and SAC405] solders subjected to thermal cycling loadings and isothermal ageing. The solders form the joints between the BGAs and printed circuit boards (PCBs). ANSYS R19.0 package is used to simulate isothermal ageing of some of the assemblies at − 40°C, 25°C, 75°C and 150°C for 45 days and model the thermal cycling history of the other assemblies from 22°C ambient temperature for six cycles. The response of the solders is simulated using the Garofalo-Arrhenius creep model. Under thermal ageing, SAC396 solder joints demonstrate possession of least strain energy density, deformation and von Mises stress in comparison to the other solders. Under thermal cycle loading conditions, SAC405 acquired the lowest amount of the damage parameters in comparison. Lead-free SAC405 and SAC387 joints accumulated the lowest and highest energy dissipation per cycle, respectively. It is concluded that SAC405 and SAC396 are the most effective solders for BGA in devices experiencing isothermal ageing and temperature cycling during operation, respectively. They are proposed as the suitable replacement of eutectic Sn63Pb37 solder for the various conditions.

18 April 2020 in Advances in Materials and Processing Technologies
Verified
Journal Article
Closed access
JDJoshua Adeniyi Depiver
Joshua Adeniyi Depiver
SMSabuj Mallik
Sabuj Mallik
DHDani Harmanto
Dani Harmanto
Solder joints play a critical role in electronic devices by providing electrical, mechanical and thermal interconnections. These miniature joints are also the weakest links in an electronic device. Under severe thermal and mechanical loadings, solder joints could fail in ‘tensile fracture, fatigue failure and creep failure. This paper reviews the literature on solder joint failures under thermo-mechanical loading conditions, with a particular emphasis on fatigue and creep failures. Literature reviews mainly focused on commonly used lead-free Sn-Ag-Cu (SAC) solders. Based on the literature in experimental and simulation studies on solder joints, it was found that fatigue failures are widely induced by accelerated thermal cycling (ATC). During ATC, the mismatch in coefficients of thermal expansion (CTE) between different elements of electronics assembly contributes significantly to induce thermal stresses on solder joints. The fatigue life of solder joints is predicted based on phenomenological fatigue models that utilise materials properties as inputs. A comparative study of 14 different fatigue life prediction models is presented with their relative advantages, scope and limitations. A critical review of various creep models is presented. Finally, the paper outlined the combined effect of creep and fatigue on solder joint failure.

23 April 2023 in Journal of Electronic Materials
Verified
Journal Article
Open access
PDF file
JDJoshua Adeniyi Depiver
Joshua Adeniyi Depiver
SMSabuj Mallik
Sabuj Mallik
EAEmeka H. Amalu
Emeka H. Amalu
Solder interconnection in electronic packaging is the weakest link, thus driving the reliability of electronic modules and systems. Improving interconnection integrity in safety-critical applications is vital in enhancing application reliability. This investigation qualifies the random vibration response of five essential solder compositions in ball grid array (BGA) solder joints used in safety-critical applications. The solder compositions are eutectic Sn63Pb37 and SnAgCu (SAC) 305, 387, 396, and 405. Computer-aided engineering (CAE) employing ANSYS finite element analysis and SolidWorks software is implemented in this investigation. The solder Sn63Pb37 deformed least at 0.43 µm, followed by SAC396 at 0.58 µm, while SAC405 deformed highest at 0.88 µm. Further analysis demonstrates that the possession of a higher elastic modulus and mass density culminates in lower solder joint deformation. Stress is concentrated at the periphery of the solder joints in contact with a printed circuit board (PCB). The SAC396 solder accumulates the lowest stress of 14.1 MPa, followed by SAC405 at 17.9 MPa, while eutectic Sn63Pb37 accrues the highest at 34.6 MPa. Similarly, strain concentration is found at the interface between the solder joint and copper pad on a PCB. SAC405 acquires the lowest elastic strain magnitude of 0.0011 mm/mm, while SAC305 records the highest strain of 0.002 mm/mm. These results demonstrate that SAC405 solder has maximum and SAC387 solder has minimum fatigue lives.

15 September 2020
Verified
Conference Paper
Closed access
JDJoshua Adeniyi Depiver
Joshua Adeniyi Depiver
SMSabuj Mallik
Sabuj Mallik
EAEmeka H. Amalu
Emeka H. Amalu
While the fatigue behaviours (including fatigue life predictions) of lead-free solder joints have been extensively researched in the last 15 years, these are not adequately compared and benchmarked for different lead-free solders that are being used. As more and more fatigue properties of lead-free solders are becoming available, it is also critical to know how fatigue behaviours differ under different mathematical models. This paper addresses the challenges and presents a comparative study of fatigue behaviours of various mainstream lead-free Sn-Ag-Cu (SAC) solders and benchmarked those with lead-based eutectic solder. Creep-induced fatigue and fatigue life of lead-based eutectic Sn63Pb37 and four lead-free SAC solder alloys: SAC305, SAC387, SAC396 and SAC405 are analysed through simulation studies. The Anand model is used to simulate the inelastic deformation behaviour of the solder joints under accelerated thermal cycling (ATC). It unifies the creep and rate-independent plastic behaviour and it is used to predict the complex stress-strain relationship of solders under different temperatures and strain rates, which are required in the prediction of fatigue life using the fatigue life models such as Engelmaier, Coffin-Mason and Solomon as the basis of our comparison. The ATC was carried out using temperature range from −40°C to 150°C. The fatigue damage propagation is determined with finite element (FE) simulation, which allows virtual prototyping in the design process of electronics devices. The simulation was carried out on a BGA (36 balls, 6 × 6 matrix) mounted onto Cu padded substrate. Results are analysed for plastic strain, Von mises stress, strain energy density, and stress-strain hysteresis loop. The simulation results show that the fatigue behaviours of lead-based eutectic Sn63Pb37 solder is comparable to those of lead-free SAC solders. Among the four SAC solders, SAC387 consistently produced higher plastic strain, strain energy and stress than the other solders. The fatigue life’s estimation of the solder joint was investigated using Engelmaier, Coffin-Manson, and Solomon models. Results obtained show that SAC405 has the highest fatigue life (25.7, 21.1 and 19.2 years) followed by SAC396 (18.7, 20.3 and 17.9 years) and SAC305 (15.2, 13.6 and 16.2 years) solder alloys respectively. Predicting the fatigue life of these solder joints averts problems in electronics design for reliability and quality, which if not taken care of, may result in lost revenue. Predictive fatigue analysis can also considerably reduce premature failure, and modern analysis technique such as one used in this research is progressively helping to provide comprehensive product life expectancy data.

1 December 2019
Verified
Conference Paper
Open access
JDJoshua Adeniyi Depiver
Joshua Adeniyi Depiver
SMSabuj Mallik
Sabuj Mallik
DHDani Harmanto
Dani Harmanto
EAEmeka H. Amalu
Emeka H. Amalu
Solder joints of electronic components are the most critical part of any electronic device. Their untimely failure during the system's operation often culminates in catastrophic failure of the device. The determination of creep damage in electronic component solder joint is vital to the prediction of crack initiation and prevention of premature failure. This paper presents the creep damage in solder joints in a ball grid array (BGA) soldered on a printed circuit board (PCB) and subjected to thermal cycling as well as isothermal ageing. ANSYS 19.0 package is employed to model the isothermal ageing at −40, 25, 75 and 150°C temperatures for 45 days. Standard temperature cycle profile is used to simulate the effect of the coefficient of thermal expansion (CTE) mismatch on the bonded materials in the BGA component. The solders studied are lead-based eutectic solder alloy and lead-free SAC396, SAC387, and SAC305. Based on the results obtained for the stress, strain rate, deformation rate and strain energy of the solders, the research investigation advises on the most effective solder for achieving improvement in the thermo-mechanical reliability of solder joints in BGA soldered on PCB.