Atichat Wongkoblap

Dr. Atichat Wongkoblap

School of Chemical Engineering, Suranaree University of Technology, Nakhon Ratchasima, Thailand
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 July 2023 in Molecules
Verified
Journal Article
Open access
PDF file
SISupawan Inthawong
Supawan Inthawong
AWAtichat Wongkoblap
Atichat Wongkoblap
WIWorapot Intomya
Worapot Intomya
CTChaiyot Tangsathitkulchai
Chaiyot Tangsathitkulchai
Activated carbon derived from longan seeds in our laboratory and commercial activated carbon are used to investigate the adsorption of methane (CH4) and carbon dioxide (CO2). The adsorption capacity for activated carbon from longan seeds is greater than commercial activated carbon due to the greater BET area and micropore volume. Increasing the degree of burn-off can enhance the adsorption of CO2 at 273 K from 4 mmol/g to 4.2 and 4.8 mmol/g at 1000 mbar without burn-off, to 19 and 26% with burn-off, respectively. This is because an increase in the degree of burn-off increases the surface chemistry or concentration of functional groups. In the investigation of the effect of the hydroxyl group on the adsorption of CO2 and CH4 at 273 K, it is found that the maximum adsorption capacity of CO2 at 5000 mbar is about 6.4 and 8 mmol/g for cases without and with hydroxyl groups contained on the carbon surfaces. The opposite behavior can be observed in the case of methane, this is due to the stronger electrostatic interaction between the hydroxyl group and carbon dioxide. The simulation results obtained from a Monte Carlo simulation method can be used to support the mechanism in this investigation. Iron oxide is added on carbon surfaces with different concentrations to reveal the effects of ferric compounds on the adsorption of CO2. Iron at a concentration of about 1% on the surface can improve the adsorption capacity. However, excessive amounts of iron led to a limited adsorption capacity. The simulation result shows similar findings to the experimental data. The findings of this study will contribute to the progress of gas separation technologies, paving the way for long-term solutions to climate change and greenhouse gas emissions.

21 January 2021 in Processes
Verified
Journal Article
Open access
PDF file
CTChaiyot Tangsathitkulchai
Chaiyot Tangsathitkulchai
SNSuravit Naksusuk
Suravit Naksusuk
AWAtichat Wongkoblap
Atichat Wongkoblap
PPPoomiwat Phadungbut
Poomiwat Phadungbut
PBPrapatsorn Borisut
Prapatsorn Borisut
The equilibrium and kinetics of CO2 adsorption at 273 K by coconut-shell activated carbon impregnated with sodium hydroxide (NaOH) was investigated. Based on nitrogen adsorption isotherms, porous properties of the tested activated carbons decreased with the increase of NaOH loading, with the decrease resulting primarily from the reduction of pore space available for nitrogen adsorption. Equilibrium isotherms of CO2 adsorption by activated carbons impregnated with NaOH at 273 K and the pressure up to 100 kPa displayed an initial part of Type I isotherm with most adsorption taking place in micropores in the range of 0.7–0.9 nm by pore-filling mechanisms. The amount of CO2 adsorbed increased with the increase of NaOH loading and passed through a maximum at the optimum NaOH loading of 180 mg/g. The CO2 isotherm data were best fitted with the three-parameter Sips equation, followed by Freundlich and Langmuir equations. The pore diffusion model, characterized by the effective pore diffusivity (De), could well describe the adsorption kinetics of CO2 in activated carbons impregnated with NaOH. The variation of De with the amount of CO2 adsorbed showed three consecutive regions, consisting of a rapid decrease of De for CO2 loading less than 40 mg/g, a relatively constant value of De for the CO2 loading of 40–80 mg/g and a slow decrease of De for the CO2 loading of 80–200 mg/g. The maximum De occurred at the optimum NaOH loading of 180 mg/g, in line with the equilibrium adsorption results. The values of De varied from 1.1 × 10−9 to 5.5 × 10−9 m2/s, which are about four orders of magnitude smaller than the molecular diffusion of CO2 in air. An empirical correlation was developed for predicting the effective pore diffusivity with the amount of CO2 adsorbed and NaOH loading.

21 April 2021 in Molecules
Verified
Journal Article
Open access
PDF file
PKPakamas Kohmuean
Pakamas Kohmuean
WIWorapoj Inthomya
Worapoj Inthomya
AWAtichat Wongkoblap
Atichat Wongkoblap
CTChaiyot Tangsathitkulchai
Chaiyot Tangsathitkulchai
Adsorption of carbon dioxide and methane in porous activated carbon and carbon nanotube was studied experimentally and by Grand Canonical Monte Carlo (GCMC) simulation. A gravimetric analyzer was used to obtain the experimental data, while in the simulation we used graphitic slit pores of various pore size to model activated carbon and a bundle of graphitic cylinders arranged hexagonally to model carbon nanotube. Carbon dioxide was modeled as a 3-center-Lennard-Jones (LJ) molecule with three fixed partial charges, while methane was modeled as a single LJ molecule. We have shown that the behavior of adsorption for both activated carbon and carbon nanotube is sensitive to pore width and the crossing of isotherms is observed because of the molecular packing, which favors commensurate packing for some pore sizes. Using the adsorption data of pure methane or carbon dioxide on activated carbon, we derived its pore size distribution (PSD), which was found to be in good agreement with the PSD obtained from the analysis of nitrogen adsorption data at 77 K. This derived PSD was used to describe isotherms at other temperatures as well as isotherms of mixture of carbon dioxide and methane in activated carbon and carbon nanotube at 273 and 300 K. Good agreement between the computed and experimental isotherm data was observed, thus justifying the use of a simple adsorption model.


20 February 2019 in MATEC Web of Conferences
Verified
Journal Article
Open access
SDSujitra Doungsri
Sujitra Doungsri
PRP. Rattanaphanee
P. Rattanaphanee
AWAtichat Wongkoblap
Atichat Wongkoblap
Lactic acid (LA), one of the important biomass derived platform chemicals, has been used in food and chemical industries, especially in biodegradable polymer as polylactic acid (PLA). The aim of this work is to study the one-pot production of LA from cellulose by using different solid catalysts. The reaction was conducted in a high pressure batch reactor and the catalyst used in this study were ZrO2 and Al2O3. The reaction was carried out at temperature of 200oC for 6 hr. and under nitrogen pressure of 1 MP. It was found that the production yield of LA were 8.02% and 6.63%, when the ZrO2 and Al2O3 catalysts were used respectively. The result indicated that the ZrO2 may effect on the LA production because of the acid and base sites of the ZrO2. Therefore, the reaction pathways for conversion of cellulose into lactic acid have been investigated, and developed the new conditions to achieve the higher yield.

7 October 2020 in Processes
Verified
Journal Article
Open access
PDF file
CBChontira Boonfung
Chontira Boonfung
CTChaiyot Tangsathitkulchai
Chaiyot Tangsathitkulchai
AWAtichat Wongkoblap
Atichat Wongkoblap
Experimental and simulation studies for carbon dioxide (CO2) adsorption on porous silica glass were performed to reveal how surface heterogeneity can affect the adsorption mechanism of CO2. In performing the simulation, the structure of porous silica glass was modeled as a slit pore consisting of parallel walls of connected SiO4 units. The adsorption isotherms of CO2 at 283 K were generated for a series of pore widths using a Monte Carlo ensemble. The defective surfaces created by random removal of surface atoms and the surfaces containing hydroxyl functional groups were chosen to represent the surface heterogeneity for the simulation tasks. The isotherms derived for the defective surfaces showed a rapid adsorption at low pressures because of the stronger interaction between the rough nonuniform surfaces and CO2 molecules. For the role of surface functional groups, the adsorption isotherms dramatically increased with an increasing number of functional groups. The amount of CO2 adsorbed for randomly placed functional groups was greater than that for the presence of functional groups at the pore edges. The proper control of surface heterogeneity by manipulating both the amounts of hydroxyl surface groups and surface defects should help enhance the efficient capture of CO2 in porous silica glass.