A 10 mm narrow gap TC4 titanium alloy welded joint by laser welding with filler wire was obtained by different welding heat inputs. The microstructures of the welded joint were analyzed by OM, SEM, XRD and EBSD. The mechanical properties of the welded joint were analyzed by microhardness test and tensile test. The results show that with the increase of laser welding heat input, the average grain size and width of the equiaxed crystal zone in the center of the weld increases, the grain angle in the columnar crystal zone gradually tends to be perpendicular to the center of the weld, and the width of the heat affected zone (HAZ) increases without obvious grain coarsening. The HAZ of the welded joint is softened, and its microhardness value is lower than that of the weld and the base metal. The tensile strength of the welded joint is slightly higher than those of the base metal, but the elongation after fracture is less than that of the base metal, and it decreases with the increase of laser welding heat input.

Metal fabrications experience complex physical metallurgical processes during additive manufacturing, leading to residual stress and coarse microstructure with directional growth. It significantly affects the comprehensive performance of the fabrications, which limits the application of additive manufacturing. Ultrasonic impact treatment (UIT), as a strengthening means to assist additive manufacturing, can effectively improve the stress state and refine the microstructure and the comprehensive performance. This paper introduces the effect of UIT on AM metal fabrications on microstructure morphology, stress distribution, surface roughness, internal defects, and comprehensive performance to gain a deeper understanding of the role of UIT on additively manufactured metal fabrications, which is based on the working principle and effect of process parameters. In addition, the strengthening mechanism of UIT in additive manufacturing is described from the perspective of surface plastic deformation and substructure formation, providing support for the shape and property control of metal fabrications in the process of additive manufacturing assisted by UIT. Finally, the issues that need to be studied in depth on UIT in additive manufacturing are summarized, and an outlook on future research directions is taken.

Through in situ observation at high temperature confocal laser scanning microscope, the microstructures and phase transformation of Ti-6Al-4V titanium alloy welded joint by laser welding with filler wire during heating, heat preservation and cooling process in simulating welding thermal cycle were studied. When the weld microstructure was heated to 380 °C, obvious grain growth was observed. After heating to 1 050 °C, weld microstructures were mostly composed of coarse β-columnar grains. During the heat preservation process of the weld metal, it could be found that the β phase boundary moved slowly. In the cooling process of weld microstructures, with the increase of the cooling rate, the transition temperature for new phase precipitation decreased gradually, and that for ending the precipitation increased gradually. The microstructures after cooling to room temperature at a rate of 0.5 °C/s and 5 °C s⁻¹ were composed of α phases. At 20 °C s⁻¹, acicular α′ martensite appeared in the microstructures. At 80 °C s⁻¹, precipitated phases were all composed of acicular α′ martensite.The Ti-6Al-4V titanium alloy weld microstructure by laser welding with filler wire is completely hexagonal close packed (HCP) crystal structure.The hardness of the weld microstructures was improved with the cooling rate getting faster.

The evolution of austenite, acicular ferrite, upper bainite and martensite, and the nucleation of inclusions in the microstructure of high-strength steel deposited metals, was systematically investigated using three kinds of A5.28 E120C-K4 metal-cored wires with various rare earth Pr contents. Grain structure evolution in the process of high temperature, dispersoid characteristics of inclusions and the crystallographic characteristics of the microstructure were assessed. Compared with no addition of Pr₆O₁₁, adding 1%Pr₆O₁₁ resulted in refined, spheroidized and dispersed inclusions in the deposited metal, leading to an increase in the pinning forces on the grain boundary movement, promoting the formation of an ultra-fine grain structure with an average diameter of 41 μm. The inclusions in the deposited metals were Mn-Si-Pr-Al-Ti-O after Pr addition; the average size of the inclusions in the Pr-containing deposited metals was the smallest, while the number and density of inclusions was the highest. The size of effective inclusions (nucleus of acicular ferrite formation) was mainly in the range of 0.6–1.5 μm. In addition, the content of upper bainite decreased, while the percentage of acicular ferrite increased by 24% due to the increase in the number of effective inclusions in the Pr-containing deposited metals in this study. This study shows that the addition of 1% Pr₆O₁₁ is efficient in achieving fine interlaced multiphase with an ultrafine-grained structure, resulting in an enhancement of the impact toughness of the deposited metal.

A self-developed Ti-Al-V-Mo system titanium alloy flux-cored wire was used to join the Ti64 titanium alloy plate via laser welding with filler wire. The microstructure and properties of the obtained welded joint were investigated. The results showed the WM (welded metal) of the welded joint consisted mainly of acicular α’ martensite, and the HAZ (heat affected zone) was comprised of a primary α_p phase, Widmanstatten, and a few α’ martensite and a residual β phase. The strength and elongation of the welded joint after breaking are equivalent to that of the BM (base metal). The tensile fracture, presenting as a microvoid coalescence ductile fracture, was encompassed by massive shear lips with deep and uniform dimples. The overall microhardness of the welded joint was sequenced as WM > HAZ > BM. In the WM, large-angle grain boundaries with intragranular misorientation greater than 15° accounted for about 84%. By XRD, it was discovered the welded joint was mainly composed of the α’ martensite, with a modest amount of extremely weak multi-angle α phase diffraction peak. The test results showed the designed welding method of titanium flux-cored wire and laser wire filling is suitable for high-quality welding of titanium alloy plate.