The excellent casting behavior and mechanical and corrosion properties of aluminum-silicon (Al-Si)-based alloys make them ideal for the manufacture of lightweight components with complex geometries. However, these properties depend directly on their microstructure, which, in its turn, is strongly affected by the composition of the alloy, among other factors. Several elements can be added to the material aiming to promote microstructural changes, e.g., grain refinement, optimization of phase morphology and distribution, and precipitation strengthening. Efforts are continuously put into such enhancements of cast Al alloys since they lead to quality improvements that allow for weight reduction and safety increase. Considering the technological relevance of the subject, this paper provides an overview of the research focused on the addition of alloying elements to these alloys, with a greater focus on Al-Si-based systems and the comprehension of the effects of these additions on their microstructure and properties.
High-strength steels such as Dual Phase (DP), Transformation-Induced Plasticity (TRIP), and Twinning-Induced Plasticity (TWIP) steels have gained importance in automotive applications due to the potential for weight reduction and increased performance in crash tests. However, as resistance increases, there is also an increase in springback due to residual stresses after the forming process. This is mainly because of the greater elastic region of these materials and other factors associated with strain hardening, such as the Bauschinger effect, that brings theory of kinematic hardening to mathematical modeling. This means that finite element software must consider these properties so that the simulation can accurately predict the behavior. Currently, this knowledge is still not widespread since it has never been used in conventional materials. Additionally, engineers and researchers use the Forming Limit Diagram (FLD) curve in their studies. However, it does not fully represent the actual failure limit of materials, especially in high-strength materials. Based on this, the Fracture Forming Limit Diagram (FFLD) curve has emerged, which proposes to resolve these limitations. Thus, this review aims to focus on how finite element methods consider all these factors in their modeling, especially when it comes to the responses of high-strength steels.
Superduplex stainless steels (SDSS) are known for their combination of good mechanical properties and excellent corrosion resistance, enabled by the microstructural balance between austenite and ferrite and an amount of alloying elements. Their application in welded components is, however, limited by the possibility of the precipitation of intermetallic phases and microstructural misbalance, which might hinder their properties, especially in the heat-affected zone (HAZ). This work introduces a methodology that relies simultaneously on physical and numerical simulations to study the HAZ in a UNS S32750 SDSS. Dimensions of the fusion zone and thermal cycles were calibrated for a numerical model using preliminary welding trials. Numerically simulated cycles for each heat input (HI) were physically reproduced in a Gleeble® simulator, and the heat-treated samples were characterized and compared with real specimens welded using the same parameters. Thermal curves resulting from the numerical simulations were successfully replicated by the Gleeble®, indicating adequate application of the desired HI. The hardness and microstructural results from simulated and welded specimens were also found to be quite similar. Therefore, the proposed methodology showed itself adequate not only for the study of duplex stainless steels, but also of materials with similar thermal and mechanical properties, including the extrapolation of welding parameters.
19 May 2023 in Journal of Materials Research and Technology
Styrene–ethylene–butylene–styrene (SEBS) copolymer, grafted or not, with maleic anhydride and organophilic montmorillonite clay was melt mixed with polypropylene (PP) using different mixing sequences to understand its effect on properties and morphology. The addition of clay changed the blend morphology from large elongated domains to droplets. The nanocomposites without maleic anhydride presented clay in the intercalated form. In the formulation containing maleic anhydride, clay is exfoliated on the blend, indicating that the maleic anhydride group acted to increase the interaction between the clay lamellae and the polymer chains. The best balance of mechanical properties was achieved in the formulation in which the clay was first melt mixed in SEBS without maleic anhydride and afterward melt mixed with clay and PP. It is reported in the literature that nanocomposites with exfoliated structures have better mechanical properties than nanocomposites with intercalated structure. However, in this study, an opposite trend was found, which may be related to the higher amount of crystalline phase formed in the intercalated structure nanocomposites, since the clay intercalation phenomenon in the polymer chains favored the polymer crystallization process.
23 December 2023 in Journal of Materials Research and Technology
Lamellar and partially spheroidized pearlitic microstructures were lab-manufactured via, respectively, stress relief treatment at 400 (SR400) and 700 °C (SR700) for 60 s. The performance of both microstructures under four successive three-point bending (TPB) tests was investigated via in-situ secondary electron imaging in scanning electron microscopy. Additionally, consecutive interruptions after each TPB were performed for electron backscatter diffraction (EBSD) analyses. Transmission-EBSD and scanning transmission electron microscopy were employed in the starting specimens: SR400 and SR700. Initially, SR400 presented many shear bands, while SR700 depicted small recrystallized grain zones with coarse spheroidized cementite. Additionally, Bagaryatskii and Isaichev cementite/ferrite orientation relationships were found for SR400 and SR700, respectively. During TPB deformation, SR400 exhibited high strength and stable mechanical behavior, while SR700 displayed a softening phenomenon and earlier failure. Moreover, the EBSD analyses indicated that strains were concentrated in the shear bands of SR400 and the small recrystallized grain zones of SR700 during TPB. The small recrystallized grain zones with coarse spheroidized cementite were related to promoting the earlier damage and, consequently, failure of SR700. Finally, the more significant presence of sheared areas and elongated dimples on the SR400's fractured surface demonstrated its higher capacity to support plastic deformation under TPB than SR700.