A dramatic rise in research interest in laser‐induced graphene oxide (GO) reduction and modification requires an overview of the most recent works on this subject. Typical methods for the recognition and confirmation of modified graphene and its derivatives, such as Raman, Fourier‐transform infra‐red (FTIR), X‐ray photoelectron (XP), and ultraviolet‐visible (UV–vis) spectroscopies, are introduced briefly in this review. A major part of the survey is devoted to the main modification ways and the laser parameters used in the literature. A discussion of possible reduction and modification mechanisms is also presented. Recent applications, especially in the biomedical field such as cell therapy treatment, as well as significant results of GO modification, are discussed in detail. Finally, perspectives for the application of laser‐induced GO modifications in passive THz photonics and biomedicine are briefly addressed.

One-pot hydrothermal synthesis of MoS₂ nanoplatelet arrays on various substrates is perhaps the most promising approach to fabricate efficient electrocatalysts for hydrogen evolution reaction. However, the main challenges in this synthesis remain the purity and crystallinity of MoS₂. In this study, we show for the first time that irradiation of amorphous, defect-rich MoS₂ nanoplatelets with a green nanosecond laser at a proper irradiation dose, ca ≤0.35 J cm⁻², can significantly improve the crystallinity and purity of MoS₂ nanoplatelets. The effect was confirmed by Raman spectroscopy investigations demonstrating a surprising intensity increase of the A¹_g and "Equation missing"<!-- image only, no MathML or LaTex --> modes after the laser irradiation. Further increase of irradiation energy, however, resulted in the photocorrosion and destruction of MoS₂ nanoplatelets. The variation of A¹_g and "Equation missing"<!-- image only, no MathML or LaTex --> Raman mode intensities ratio depending on the green light irradiation dose was also presented and is discussed below.

The Internet of Things (IoT) technology and its applications are turning real-world things into smart objects, integrating everything under a common infrastructure to manage performance through a software application and offering upgrades with integrated web servers in a timely manner. Quality of life, the green economy, and pollution management in society require comprehensive environmental monitoring systems with easy-to-use features and maintenance. This research suggests implementing a wireless sensor network with embedded sensor nodes manufactured using the Selective Surface Activation Induced by Laser technology. Such technology allows the integration of electrical circuits with free-form plastic sensor housing. In this work, a low-cost asynchronous web server for monitoring temperature and humidity sensors connected to the ESP32 Wi-Fi module has been developed. Data from sensor nodes across the facility are collected and displayed in real-time charts on a web server. Multiple web clients on the same network can access the sensor data. The energy to the sensor nodes could be powered by harvesting energy from surrounding sources of electromagnetic radiation. This automated and self-powered system monitors environmental and climatic factors, helps with timely action, and benefits sensor design by allowing antenna and rf-circuit formation on various plastics, even on the body of the device itself. It also provides greater flexibility in hardware modification and rapid large-scale deployment.

Our study presents laser-assisted methods to produce conductive graphene layers on the polymer surface. Specimens were treated using two different lasers at ambient and nitrogen atmospheres. A solid-state picosecond laser generating 355 nm, 532 nm, or 1064 nm wavelengths and a CO₂ laser generating mid-infrared 10.6 µm wavelength radiation operating in a pulsed regime were used in experiments. Sheet resistance measurements and microscopic analysis of treated sample surfaces were made. The chemical structure of laser-treated surfaces was investigated using Raman spectroscopy, and it showed the formation of high-quality few-layer graphene structures on the PI surface. The intensity ratios I(2D)/I(G) and I(D)/I(G) of samples treated with 1064 nm wavelength in nitrogen atmosphere were 0.81 and 0.46, respectively. After laser treatment, a conductive laser-induced graphene layer with a sheet resistance as low as 5 Ω was formed. Further, copper layers with a thickness of 3–10 µm were deposited on laser-formed graphene using a galvanic plating. The techniques of forming a conductive graphene layer on a polymer surface have a great perspective in many fields, especially in advanced electronic applications to fabricate copper tracks on 3D materials.