Jong-Sung Kim

Prof. Jong-Sung Kim

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 July 2020 in Journal of Mechanical Science and Technology
Verified
Journal Article
Closed access
PDF file
JKJong-Sung Kim
Jong-Sung Kim
MKMaan-Won Kim
Maan-Won Kim
JYJun-Seok Yang
Jun-Seok Yang

14 September 2021 in Metals and Materials International
Verified
Journal Article
Open access
PDF file
JLJunsang Lee
Junsang Lee
JKJong-Sung Kim
Jong-Sung Kim
BLBongsang Lee
Bongsang Lee
SCSungwoo Cho
Sungwoo Cho
DKDongil Kwon
Dongil Kwon
JKJong-Hyoung Kim
Jong-Hyoung Kim
This study analyzes the effects of post-weld heat treatment (PWHT) on the mechanical properties and microstructures of SA-508 Gr.1a welds and proposes a new PWHT exemption criterion based on nonductile fracture evaluation considering welding residual stress. The welding coupons were prepared with submerged-arc welding, gas-tungsten arc welding, and shielded-metal arc welding, using ferritic steel, SA-508 Gr.1a. The microstructure of the heat-affected zone (HAZ) was analyzed using optical microscopy, electron-back-scatter diffraction and Vickers hardness testing. The mechanical properties of the welds were evaluated by uniaxial tensile test, transverse side bend test, Charpy V-notch impact test and side bend test. Bainite and ferrite structures formed mainly in the HAZ, and the grain size became coarser with proximity to the surface and fusion line. The mechanical properties did not depend strongly on PWHT, weldment thickness or welding techniques, and they satisfied the welding procedure qualification test specified in the ASME Boiler & Pressure Vessel code. Welding residual stresses were considered in assessing structural integrity using nonductile fracture evaluation. A margin of safety against nonductile fracture with residual stress was calculated for Korean Standard Nuclear Power Plant steam-generator welds, using its design parameters and operating conditions, and this safety margin is suggested as an acceptance criterion for residual stress for exemption from PWHT. Graphic abstract

1 July 2021 in International Journal of Mechanical Sciences
Verified
Journal Article
Closed access
GYGyo-Geun Youn
Gyo-Geun Youn
YKYun-Jae Kim
Yun-Jae Kim
JKJong-Sung Kim
Jong-Sung Kim
PLPoh-Sang Lam
Poh-Sang Lam

27 August 2020 in Energies
Verified
Journal Article
Open access
PDF file
GKGyeong-Hoi Koo
Gyeong-Hoi Koo
JKJong-Sung Kim
Jong-Sung Kim
YKYun-Jae Kim
Yun-Jae Kim
In this paper, the feasibility study to develop strain-based seismic design criteria applicable for the components of nuclear power plants are carried out as an alternative rule to the current stress-based criteria. To do this, two acceptance criteria are investigated through the detailed example of an application for the surge line nozzles in a nuclear steam supply system, which are known as one of the seismic fragile components in nuclear power plants. These strain-based seismic design criteria are primarily to prevent two types of failure modes, such as a ductile fracture and a cyclic fatigue-induced damage due to continuous large amplitude cyclic loads during seismic event. Through the example problem, the required procedures are described step-by-step with calculations of an accumulated plastic strain, triaxiality factor by the elasto-plastic seismic analysis using the finite element method. For a precise inelastic seismic analysis, the Chaboche kinematic and Voce isotropic hardening material parameters are identified by the test data and used for an inelastic material model. The results by the strain-based criteria are compared with those by the ASME (American Society of Mechanical Engineers) stress-based design criteria for a service level D limits. From the study, it is expected that the strain-based seismic design method investigated in this paper will be beneficial for the nuclear components, especially when the design basis earthquakes are large enough to cause severe plastic strains at a critical location.