Selective laser sintering (SLS) is being developed for dental applications. This study aimed to investigate the properties of Ti-6Al-4V and pure titanium specimens fabricated using the SLS process and compare them with casting specimens. Besides, the effect of the building direction on the properties of the SLS specimens was also investigated. Specimens were prepared by SLS using Ti-6Al-4V powder or pure titanium powder. Casting specimens were also prepared using Ti-6Al-4V alloys and pure titanium. The mechanical properties (tensile strength and elongation), physical properties (surface roughness, contact angle, and Vickers hardness); corrosion resistors (color difference and corrosion), and surface properties (chemical composition and surface observation) were examined. Both Ti-6Al-4V and pure titanium specimens produced using the SLS process had comparable or superior properties compared with casting specimens. In comparing the building directions, specimens fabricated horizontally to the printing platform showed the greatest tensile strength, and the surface roughness scanned in the horizontal direction to the platform showed the smallest. However, there was no significant effect on other properties. Thus, the SLS process with Ti-6Al-4V powder and pure titanium powder has great performance for the fabrication of dental prosthesis, and there is a possibility for it to take the place of conventional methods.

Objective: This study investigates the reliability of different flexural tests such as three-point-bending, four-point bending, and biaxial tests, in strengthening the dental pressed ceramics (DPCs) frequently used in clinical applications. Methods: The correlations between the three types of bending tests for DPCs were investigated. Plate-shaped specimens for the three-point and four-point bending tests and a disc-shaped specimen for the biaxial bending test were prepared. Each bending test was conducted using a universal testing machine. Results: The results for six DPCs showed that the flexural strength in descending order were the three-point flexural strength, biaxial flexural strength, and four-point flexural strength, respectively. Then, a regression analysis showed a strong correlation between each of the three test methods, with the combination of four-point and biaxial flexural strength showing the highest values. The biaxial flexural strength was not significantly different in the Weibull coefficient (m) compared to the other tests, with the narrowest range considering the 95% interval. The biaxial bending test was found to be suitable for materials with small plastic deformation from the yield point to the breaking point, such as DPCs.

The polymerization shrinkage values of commercial flowable and conventional composites were measured with a newly developed laser displacement sensor. Compressive strength and filler content were also measured. Compared to conventional composites, the flowable composites required a longer time — not exceeding 4 minutes — to reach a constant polymerization shrinkage rate. In terms of shrinkage ratio, it was less than 1.5% for conventional composites at 90 minutes, which was lower than that of flowable composites, i.e. more than 2.0%. The compressive strength of conventional composites was higher than that of flowable composites. A highly significant correlation between filler content and polymerization shrinkage at 90 minutes was observed, and polymerization shrinkage tended to decrease as filler content increased. In light of the results obtained in this study, the newly developed displacement meter with a laser displacement sensor proved to be effective for in-depth investigation of the polymerization shrinkage of dental composites.

The bonding efficacy of aqueous solutions of two kinds of erythritol methacrylates as dentin primers was examined by measurement of the polymerization contraction gap of a light-activated resin composite in a cylindrical dentin cavity and the tensile bond strength of the composite to the flat dentin surface. The dentin surface was cleaned with neutralized 0.5 mol/L EDTA and pre-treated with a meso-erythritol or penta-erythritol methacrylate solution, followed by application of a commercial dentin bonding agent (Clearfil New Bond) and a resin composite. Among the tested primers, a 40% meso-erythritol methacrylate solution was shown to be the most effective because, in contrast to the other primers, contraction gap formation by the composite was prevented in all tested specimens.

Consumer 3D printers have improved considerably due to the evolution of additive manufacturing. This study aimed to examine the accuracy of consumer printers in dental restoration. Cylindrical patterns mimicking a full crown were created and enlarged from 100% to 105% of the original size. Two types of consumer 3D printers, including a fused deposition modeling (FDM) device and a stereolithography (SLA) device, and two types of dental 3D printers, including a multi-jet device and an SLA device, were used to fabricate the patterns. Then, the outer and inner diameters and depths, and surface roughness of the patterns were measured. The changing rates of the outer diameter of models created using dental printers were significantly smaller than those of the models created using consumer printers (p < 0.05). Significantly greater surface roughness was obtained in the tooth axis of the model fabricated using the consumer FDM device (p < 0.05). However, no significant differences were observed on the surface roughness of both axes between the consumer SLA device and the dental devices (p > 0.05). However, FDM showed larger surface roughness than dental devices in both axes (p < 0.05). Thus, the SLA consumer printer can be applied to fabricate resin patterns with enlargement editing of 1–3% along the horizontal axis.

Mercury is produced and drained into the environment by removing dental amalgams, which may cause mercury pollution. This study aimed to clarify the mercury amount remaining in the oral cavity and inside the drain system after removal. The effects of the removal conditions and differences in drainage systems were also investigated. Dental amalgams filled in the tooth and placed in a phantom head were removed using an air turbine under several conditions (two removal methods, absence of cooling water, and intraoral suction). Then, the oral cavity was rinsed with 100 mL of water (oral rinse water), and 500 mL of water was suctioned to wash the inside of the drainage system (system rinse water). Both water samples were collected in two ways (amalgam separator and gas-liquid separator), and their mercury amounts were measured. It was found that the amount of mercury left in the oral cavity and drainage system after dental amalgams removal could be reduced when the amalgams were removed by being cut into fragments as well as using cooling water and intraoral suction. In addition, using amalgam separators can significantly reduce the amount of mercury in the discharge water and prevent the draining of mercury into the environment.