This work investigates the effect and mechanisms of gas heating in atmospheric pressure air dielectric barrier discharges with experimental measurements and numerical models developed. The heating sources of a single microdischarge (MD) are evaluated by the 1.5D plasma fluid model (PFM) with heating mechanisms including elastic collisions, the ionic Joule heating, and kinetics considered. A 3D gas flow model (GFM) simulating the temperature distribution of the reactor with the convective effect of airflow considered is developed to verify heating sources calculated by comparing the simulated gas temperature with the rotational temperature determined from N 2 emission spectra measured. The source term of the energy equation in the 3D GFM is evaluated from the overall heating source calculated by the 1.5D PFM. The experimental average power consumption of the reactor is obtained and compiled statistically as 3.4 W. The average number of MDs in one cycle is compiled statistically as 140 MDs; therefore the average power consumption of a single MD obtained is around 0.024 W. The simulated power consumption of a single MD is around 0.028 W which agrees the average measured power consumption of a single MD. The heating sources of different mechanisms are evaluated by the 1.5D PFM and are provided as the average volumetric source term to the 3D GFM for evaluating the temperature distribution in the reactor. The simulated result shows that around 45% of power consumption is converted to thermal energy. The simulated average gas temperature at the center of the reactive zone is 460 K which agrees the rotational temperature determined as 470 K. Besides, both the simulated highest temperature and the temperature distribution of the reactor surface are close to those measured by the IR thermometer. The analysis of heating source finds that the ionic Joule heating and kinetics contribute to most of the heating source as 47% and 52%, respectively. Among the ionic species considered, plays the essential role and contributes to around 66% of the ionic Joule heating. Among the kinetics considered, exothermic processes contribute to most of the heating source as around 88%. Further analysis shows that the ozone generation and destruction reactions contribute to remarkable heating sources. The quenching processes of excited atomic oxygen and nitrogen species also contribute to noticeable heating sources and result in fast evolution of species densities. The N 2 ( v ) and O 2 ( v ) contribute to only a small percentage (∼10%) of the kinetic heating source under the operating conditions in this work.
1 February 2023 in Plasma Sources Science and Technology
This work investigates O3 production in a planar atmospheric pressure air dielectric barrier discharge reactor numerically and experimentally. The surface temperature of the reactor is measured by an infrared (IR) thermal imager, and the O3 densities of cases in the reactive zone are measured by ultraviolet absorption spectroscopy. The 1.5D plasma fluid model (PFM) with transverse convection is employed to capture the average properties of a single microdischarge (MD) generated in the reactor. The concept of equivalent reaction is proposed to calculate spatial-cyclic average species sources obtained by the 1.5D PFM and provided to the chemical model of a 3D gas flow model (GFM) for obtaining density distributions of reactive species generated by MDs in the reactive zone. The simulated temperature distribution of the reactor surface is validated by that measured with the IR thermal imager since the gas temperature was reported as a critical discharge parameter for O3 generation. The simulated O3 densities show the same trend as the flow rate changes, which demonstrates the proposed model captures the average discharge dynamics in different operating conditions. In the 1.5D PFM, the simulated results show that the O3 molecules produced in the case of 4 SLM are much more than those produced in the case of 1 SLM though the O atoms produced in the case of 1 SLM are around 20% more than those produced in the case of 4 SLM. In the case of 1 SLM, more than 48% of O3 molecular generated are destructed, while only around 14% of O3 molecules are destructed in the case of 4 SLM. The analysis shows that around 73% of O atoms generated in the 1.5D PFM are consumed in the formation of O3 molecules in the case of 4 SLM, while only 18% of O atoms generated in the case of 1 SLM are consumed in the formation of O3 molecules. In the 3D GFM, the O3 destructed is around 24% of that destructed in the 1.5D PFM in the case of 4 SLM due to the oxidation reaction of NO, while only 11% of O3 molecules destructed as that destructed in the 1.5D PFM in the case of 1 SLM. The amounts of O3 molecules generated in the 3D GFM are minor if they are compared with those generated in the 1.5D PFM in all cases. The overall O3 yield efficiency reaches 97 g kWh−1 with the O3 concentration increasing up to 2700 ppm in the case of 4 SLM, while the O3 yield efficiency decreases to 10 g kWh−1 and O3 concentration drops to 1400 ppm in the case of 1 SLM.
31 December 2012 in Computer Physics Communications
In this work, a semi-empirical 1.5D plasma fluid model (PFM) is proposed to model a single microdischarge (MD) in atmospheric pressure air dielectric barrier discharges (APADBDs). The species continuity equations and the electron energy density equation are solved in one-dimensional domain, while the Poisson equation is solved in the axisymmetric domain to capture the enhancement of the electric field in front of the streamer. The framework of air chemistry is considered and the effect of photoionization is modeled in the axisymmetric domain. The accumulation factor (AF) is introduced and determined by experimental data to model the accumulation of charged particles on the dielectric surface. The simulated results in two gaps are compared with experimental measurements. In the gap of 1.4 mm, the simulated electric current reaches 72 mA, which is close to the typically measured electric current. The simulated maximum wave velocity is around 1.7 × 10 6 m s −1 , which is close to the available experimental data. The change of simulated charge density implies that the average accumulation of charged particles on the dielectric surface during each half period (HP) is around 40 nC cm −2 , which is in the same order of magnitude as the average charge density evaluated in the previous measurements as 51.5 nC cm −2 . The effect of AF is studied and shows that the AF determines both peak and duration of the electric current. In the gap of 2.0 mm, the simulated current reaches 113 mA, which is close to the typically measured current. Although the gap voltage of the 2.0 mm gap is higher than that of the 1.4 mm gap, the average electric field of the 2.0 mm gap is lower than that of the 1.4 mm gap before breakdown due to larger gap distance. The maximum wave velocity is faster than that simulated in the gap of 1.4 mm due to the longer gap distance for developing higher wave velocity as 2.4 × 10 6 m s −1 . During each HP, the average accumulation of charge density on the dielectric surface reaches around 40 nC cm −2 which is almost identical to that simulated in the gap of 1.4 mm as observed experimentally. In general, the proposed semi-empirical 1.5D PFM captures the dynamics of a single MD in APADBDs.
The present work investigates contributions of different heating mechanisms and power efficiency of atmospheric-pressure helium dielectric-barrier discharges (APHeDBDs) containing a small amount of N2 for temperature measurements by developing the numerical methodology combining the one-dimensional (1D) plasma fluid model (PFM) and 3D gas flow model (GFM) with simulated results validated by measurements including the discharge power consumption and temperature distribution. The discharge dynamics are modeled by the 1D PFM for evaluating the average heating source considering elastic collision, ion Joule heating, and exothermic reactions as the source term of energy equation solved in the 3D GFM. The simulated current density reaches 29 A m−2 which is close to that measured as 35 A m−2. The simulated power consumption is 2.0 W which is in good agreement with the average measured power consumption as 2.1 W. The simulated average gas temperature in the reactive zone is around 346 K which is also close to the rotational temperature determined. The analysis shows that elastic collision and ion Joule heating are dominant heating mechanisms contributing 23.9% and 65.8% to the heating source, respectively. Among ion species, N2+ and N4+ are dominant species contributing 44.1% and 50.7% to the heating source of ion Joule heating, respectively. The simulated average total heating source is around 5.6 × 105 W m−3 with the maximum reaching 3.5 × 106 W m−3 in the sheath region due to the contribution of ion Joule heating.