In this work, we prepared highly swelling, stimuli-responsive hydrogels capable of the highly efficient adsorption of inorganic pollutants. The hydrogels were based on hydroxypropyl methyl cellulose (HPMC) grafted with acrylamide (AM) and 3-sulfopropyl acrylate (SPA) and were synthesized via the growth (radical polymerization) of the grafted copolymer chains on HPMC, which was activated by radical oxidation. These grafted structures were crosslinked to an infinite network by a small amount of di-vinyl comonomer. HPMC was chosen as a cheap hydrophilic and naturally sourced polymer backbone, while AM and SPA were employed to preferentially bond coordinating and cationic inorganic pollutants, respectively. All the gels displayed a pronounced elastic character, as well as considerably high values of stress at break (several hundred %). The gel with the highest fraction of the ionic comonomer SPA (with an AM/SPA ratio = 0.5) displayed the highest equilibrium swelling ratio (12,100%), the highest volume response to temperature and pH, and the fastest swelling kinetics, but also the lowest modulus. The other gels (with AM/SPA = 1 and 2) displayed several times higher moduli but more modest pH responses and only very modest temperature sensitivity. Cr(VI) adsorption tests indicated that the prepared hydrogels removed this species from water very efficiently: between 90 and 96% in one step. The hydrogels with AM/SPA ratios of 0.5 and 1 appeared to be promising regenerable (via pH) materials for repeated Cr(VI) adsorption.
Remarkable monolithic (non-porous) hydrogels based on poly(NIPAm-co-sodium methacrylate) intercalated by starch were prepared, and were found to display very fast and extensive one-way solvent (water) release, induced by both pH and temperature. With centimeter-sized 3D specimens, the achieved response times were as short as 4 min (for 70% water release), in combination with very large volume responses (shrinking ratios up to 15). The response time can be tuned from minutes, over tens of minutes, up to hours. The pH-induced deswelling is always slower than the temperature-induced one, but at the highest starch content, ca. 5.5 min are needed for 70% completion of the pH-triggered process. Simultaneous temperature- and pH-stimuli expectedly also lead to very fast water release. The unique intercalated structure and the temperature-dependent hydrogen bridging between the intercalated phases, as well as between these phases and water, were found to play the key role in the ability of the gels to rapidly release water and shrink, which was deeper elucidated in this work. The hydrogels are of interest as soft actuators, but also for chemical release systems or for drug release applications. The latter was successfully tested with theophylline as the drug.
This work is focused on the comparison of macro-, micro- and nanomechanical properties of a series of eleven highly homogeneous and chemically very similar polymer networks, consisting of diglycidyl ether of bisphenol A cured with diamine terminated polypropylene oxide. The main objective was to correlate the mechanical properties at multiple length scales, while using very well-defined polymeric materials. By means of synthesis parameters, the glass transition temperature (Tg) of the polymer networks was deliberately varied in a broad range and, as a result, the samples changed their mechanical behavior from very hard and stiff (elastic moduli 4 GPa), through semi-hard and ductile, to very soft and elastic (elastic moduli 0.006 GPa). The mechanical properties were characterized in macroscale (dynamic mechanical analysis; DMA), microscale (quasi-static microindentation hardness testing; MHI) and nanoscale (quasi-static and dynamic nanoindentation hardness testing; NHI). The stiffness-related properties (i.e., storage moduli, indentation moduli and indentation hardness at all length scales) showed strong and statistically significant mutual correlations (all Pearson′s correlation coefficients r > 0.9 and corresponding p-values < 0.001). Moreover, the relations among the stiffness-related properties were approximately linear, in agreement with the theoretical prediction. The viscosity-related properties (i.e., loss moduli, damping factors, indentation creep and elastic work of indentation at all length scales) reflected the stiff-ductile-elastic transitions. The fact that the macro-, micro- and nanomechanical properties exhibited the same trends and similar values indicated that not only dynamic, but also quasi-static indentation can be employed as an alternative to well-established DMA characterization of polymer networks.
4 July 2008 in Materials and Manufacturing Processes
Selected commercially available amines, including N-substituted morpholines, were evaluated as single catalysts and as catalyst mixtures for polyurethane foam preparation. The motivation was the search for economically and environmentally attractive replacements of “classical” catalysts, like diazabicyclooctane, dibutyltindilaurate, and N,N-bis(2-dimethylaminoethyl)methylamine. Especially interesting was replacing dibutyltindilaurate, and also the possibility of using reactive catalyst derivatives that would be incorporated into polyurethanes, thus reducing the content of volatile organic compounds in the polymer. The catalysts were tested on a α,ω-polybutadienediol + toluenediisocyanate-based system. In some experiments, toluenediisocyanate was replaced by the more reactive and environmentally friendly 4,4′-Methylenebis(phenylisocyanate) and polybutadienediol by polypropyleneglycol.
Amphiphilic triblock terpolymers have attractive applications in the preparation of nanoparticles with controlled morphology. An additional level of morphology control can be provided by reactive blocks, whose interactions with the solvent vary under different stimuli. In this work, we synthesized a triblock terpolymer (poly(acrylic acid)-b-poly(4-hydroxystyrene)-b-poly{1-[4-(1-methyl-1,2-dicarba-closo-dodecaborane-2-yl methyl)-phenyl]ethylene}) (PAA-b-PHS-b-PSC) containing carboranes as pendant groups by reversible addition fragmentation chain transfer (RAFT) polymerization and subsequently studied its behavior in aqueous solution. Once the nanoparticles were formed, the solubility of the second and third blocks was changed via pH and CsF reactions, respectively. The resulting micelles work as an ON/OFF system, using changes in fluorescence intensity at different pH values.