Ag has the lowest electrical resistivity among all metals, and at the same time, the best optical properties in the visible and near-IR spectral range; it is therefore the most widely employed material for thin-metal-film-based transparent conductors. In this work, an ultra-thin transparent silver film electrode with aluminum as seed layer was prepared by a resistive thermal evaporation technique. Using a range of electrical, optical and surface morphology techniques, it can be noted that the presence of the thin layer of aluminum changes the growth kinetics (nucleation and evolution) of the thermal evaporation of Ag, leading to silver films with smooth surface morphology and high electrical conductivity, and the threshold thickness of the silver film is reduced. It is inferred that the aluminum layer showed a good infiltration effect on the ultra-thin silver film, by analyzing the transmittance spectrum, sheet resistance and surface morphology. Moreover, the average transmittance of silver film with 10 nm is 40% in the 400–2500 nm band, whereas the sheet resistance is 13 Ωsq −1. A series of experiments show that the introduction of Al seed layer has certain effect on improving the properties of transparent conductive silver films. Then, a new method for deposition of 1 nm Al seed layer was proposed; that is, the 1 nm aluminum infiltrated layer is divided into two or more layers, and the average transmittance of silver film with 5 nm is 60% in the 400–2500 nm band, whereas the sheet resistance does not exceed 100 Ω sq−1.
Silver nanowires (AgNWs) are used as transparent electrodes (TE) in many devices. However, the contact mode between the nanowires is the biggest reason why the sheet resistance of silver nanowires is limited. Here, simple and effective ultraviolet (UV) irradiation welding is chosen to solve this problem. The influence of the power density of the UV irradiation on welding of the silver nanowires is studied and the fixed irradiation time is chosen as one minute. The range of the UV (380 nm) irradiation power is chosen from 30 mW/cm2 to 150 mW/cm2. First of all, the transmittance of the silver nanowire film is not found to be affected by the UV welding (400–11,000 nm). The sheet resistance of the silver nanowires decreases to 73.9% at 60 mW/cm2 and increases to 127.6% at 120 mW/cm2. The investigations on the UV irradiation time reveal that the sheet resistance of the AgNWs decreases continuously when the UV irradiation time is varied from 0 to 3 min, and drops to 57.3% of the initial value at 3 min. From 3–6 min of the continuous irradiation time, the change of the sheet resistance is not obvious, which reflects the self-limiting and self-termination of AgNWs welding. By changing the wavelength of the UV irradiation from 350–400 nm, it is found that the welding effect is best when the UV wavelength is 380 nm. The average transmittance, square resistance, and the figure of merit of the welded AgNWs at 400–780 nm are 95.98%, 56.5 Ω/sq, and 117.42 × 10−4 Ω−1, respectively. The UV-welded AgNWs are also used in silicon-based photodetectors, and the quantum efficiency of the device is improved obviously.
Transparent conductive films (TCFs) with low sheet resistance (Rsh) and high optical transmittance in the visible and infrared regions are essential components of a wide range of optoelectronic devices. Silver nanowires (AgNWs) have attracted significant attention due to their superior flexibility, conductivity, and transparency. However, TCFs prepared by commonly used film-forming methods such as spin coating suffer from a trade-off between conductivity and transmittance, which results in diminished device performance. Here we report a layer-by-layer agitation assisted alignment technique to fabricate highly aligned AgNWs films for transparent electrodes. The effects of solution concentration, rotation speed, and treatment time on the morphology, transmittance, and sheet resistance of the aligned AgNWs films were investigated systematically. Compared to randomly distributed AgNWs, optoelectronic performance was greatly improved, and the final film had a transmittance of 91.07% at 550 nm and a sheet resistance of 27.5 Ω/sq. Research findings indicate that optimized silver nanowire (AgNWs) electrodes can be successfully utilized to fabricate high-performance silicon-based photodetectors. Compared to previous designs, these detectors exhibit a 13.3% increase in external quantum efficiency at a wavelength of 850 nm. This study offers a low-cost and simple method for aligned AgNWs films, which has great potential for use in optoelectronic devices.
The ultra-thin silver film is a potential material used for transparent conductive electrodes because of its high flexibility and excellent photoelectric properties. The ultra-thin silver transparent conductive films were prepared by resistance thermal evaporation technology using aluminum as infiltration layer. The threshold thickness of the silver film was reduced by introducing an aluminum infiltration layer, so that the silver film could be continuous on the K9 glass substrate at the lowest possible thickness. The resistance of silver film squares on aluminum infiltration layers with different thicknesses was tested, and verified by scanning electron microscope (SEM) images that the 1 nm aluminum infiltration layer had better infiltration effect on silver film. Then, the silver films with different thicknesses were prepared on 1 nm aluminum infiltration layer by the same process. The transmittance and square resistance test results show that the square resistance of 10 nm silver film prepared on 1 nm aluminum infiltration layer can reach 13 Ω/□, and the transmittance can reach more than 50% in the range of 0.4 μm~2.5 μm.